Nissan Versa (N17): P0715  Input speed sensor A

Nissan Versa 2nd generation (N17) Service Manual / Transmission & driveline / Transaxle & transmission (TM) / P0715  Input speed sensor A

DTC Logic

DTC DETECTION LOGIC

DTC Trouble diagnosis name DTC detection condition Possible causes
P0715 Input/Turbine Speed Sensor A Circuit The primary speed sensor value is less than 150 rpm continuously for 5 seconds or more under the following diagnosis conditions:

- Diagnosis conditions

- Secondary pulley speed: 1,000 rpm or more

- TCM power supply voltage: More than 11 V

- Harness or connector (Primary speed sensor circuit is open or shorted)

- Primary speed sensor

The primary speed sensor value is 240 rpm or less continuously for 500 msec or more under the following diagnosis conditions:

- Diagnosis conditions

- 10-msec-ago primary pulley speed: 1,000 rpm or more

- TCM power supply voltage: More than 11 V

DTC CONFIRMATION PROCEDURE

CAUTION: Be careful of the driving speed.

1.PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.

>> GO TO 2.

2.CHECK DTC DETECTION

  1. Start the engine.
  2. Drive the vehicle.
  3. Maintain the following conditions for 10 seconds or more.
  4. Stop the vehicle.
  5. Check the first trip DTC.

Selector lever : "L" POSITION Vehicle speed : 40 km/h (25 MPH) or more

Is "P0715" detected?

YES >> Go to TM "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK PRIMARY SPEED SENSOR POWER CIRCUIT

  1. Turn ignition switch OFF.
  2. Disconnect primary speed sensor connector.
  3. Turn ignition switch ON.
  4. Check voltage between primary speed sensor harness connector terminal and ground. 

Is the inspection result normal?

YES >> GO TO 2.

NO >> GO TO 6.

2.CHECK PRIMARY SPEED SENSOR GROUND CIRCUIT

Check continuity between primary speed sensor harness connector terminal and ground. 

Is the inspection result normal?

YES >> GO TO 3.

NO >> Repair or replace malfunctioning parts.

3.CHECK CIRCUIT BETWEEN PRIMARY SPEED SENSOR AND TCM (PART 1)

  1. Turn ignition switch OFF.
  2. Disconnect TCM connector.
  3. Check continuity between primary speed sensor harness connector terminal and TCM harness connector terminal.                                                                                     

Is the inspection result normal?

YES >> GO TO 4.

NO >> Repair or replace malfunctioning parts.

4.CHECK CIRCUIT BETWEEN PRIMARY SPEED SENSOR AND TCM (PART 2)

Check continuity between primary speed sensor harness connector terminal and ground. 

Is the inspection result normal?

YES >> GO TO 5.

NO >> Repair or replace malfunctioning parts.

5.CHECK TCM INPUT SIGNALS

  1. Connect all of disconnected connectors.
  2. Lift the vehicle.
  3. Start the engine.
  4. Check frequency of primary speed sensor.

Is the inspection result normal?

YES >> Check intermittent incident. Refer to GI "Intermittent Incident".

NO >> Replace primary speed sensor. TM "Removal and Installation".

6.CHECK CIRCUIT BETWEEN IPDM E/R AND PRIMARY SPEED SENSOR (PART 1)

  1. Disconnect IPDM E/R connector.
  2. Check continuity between IPDM E/R harness connector terminal and primary speed sensor harness connector terminal.                                                

6.CHECK CIRCUIT BETWEEN IPDM E/R AND PRIMARY SPEED SENSOR (PART 1)

  1. Disconnect IPDM E/R connector.
  2. Check continuity between IPDM E/R harness connector terminal and primary speed sensor harness connector terminal.                                                                                         

Is the check result normal?

YES >> GO TO 8.

NO >> Repair or replace malfunctioning parts.

8.DETECT MALFUNCTIONING ITEMS

Check the following items:

  • Harness open circuit or short circuit between ignition switch and IPDM E/R. Refer to PG "Wiring Diagram - Ignition Power Supply -".
  • 10A fuse (No.49, IPDM E/R). Refer to PG "IPDM E/R Terminal Arrangement".
  • IPDM E/R

Is the check result normal?

YES >> Check intermittent incident. Refer to GI "Intermittent Incident".

NO >> Repair or replace malfunctioning parts.

Other materials:

Push-button ignition switch (if so equipped)
WARNING Do not operate the push-button ignition switch while driving the vehicle except in an emergency. (The engine will stop when the ignition switch is pushed 3 consecutive times in quick succession or the ignition switch is pushed and held for more than 2 seconds.) If the engine stops ...

Transmitter
Exploded View 1. Transmitter (tire pressure sensor) 2. O-ring 3. Valve stem nut 4. Valve core 5. Valve cap 6. Valve stem assembly : Parts that are replaced as a set when the tire is replaced. Removal and Installation REMOVAL Remove road wheel and tire assembly using power tool. Refe ...

Categories


© 2017-2025 Copyright www.niveguide.com
0.0078