Nissan Versa (N17): B2198 NATS antenna AMP

Nissan Versa 2nd generation (N17) Service Manual / Body exterior, doors, roof & vehicle security / Security control system (SEC) / B2198 NATS antenna AMP

DTC Logic

DTC DETECTION LOGIC       

DTC CONFIRMATION PROCEDURE

1.PERFORM DTC CONFIRMATION PROCEDURE

1. Make the conditions that BCM enters in the low power consumption mode (BCM sleep condition).

Refer to BCS "BODY CONTROL SYSTEM : System Description".

2. Turn ignition switch ON.

3. Check DTC in Self Diagnostic Result mode of BCM using CONSULT.

Is DTC detected?

YES >> Go to SEC "Diagnosis Procedure".

NO >> Inspection End.

Diagnosis Procedure

Regarding Wiring Diagram information, refer to SEC "Wiring Diagram".

1.CHECK FUSE

1. Turn power switch OFF.

2. Check that the following fuse in IPDM E/R is not blown.       

Is the inspection result normal?

YES >> GO TO 2.

NO >> Replace the blown fuse after repairing the cause of blowing.

2.CHECK NATS ANTENNA AMP. POWER SUPPLY

1. Disconnect NATS antenna amp. connector.

2. Check voltage between NATS antenna amp. harness connector and ground.   

Is the inspection result normal?

YES >> GO TO 4.

NO >> GO TO 3.

3.CHECK NATS ANTENNA AMP. POWER SUPPLY CIRCUIT

1. Disconnect IPDM E/R connector.

2. Check continuity between IPDM E/R harness connector and NATS antenna amp. connector.

Is the inspection result normal?

YES >> Replace IPDM E/R. Refer to PCS "Removal and Installation".

NO >> Repair or replace harness.

4.CHECK NATS ANTENNA AMP. GROUND CIRCUIT

Check continuity between NATS antenna amp. harness connector and ground.   

Is the inspection result normal?

YES >> GO TO 5.

NO >> Repair or replace harness.

5.CHECK NATS ANTENNA AMP. COMMUNICATION SIGNAL 1

Check voltage signal between NATS antenna amp. harness connector and ground using an oscilloscope.

Is the inspection result normal?

YES >> GO TO 7.

NO >> GO TO 6.

6.CHECK NATS ANTENNA AMP. OUTPUT SIGNAL CIRCUIT 1

1. Disconnect BCM connector.

2. Check continuity between NATS antenna amp. harness connector and BCM connector.

3. Check continuity between NATS antenna amp. harness connector and ground.

Is the inspection result normal?

YES >> GO TO 9.

NO >> Repair or replace harness.

7.CHECK NATS ANTENNA AMP. COMMUNICATION SIGNAL 2

Check voltage signal between NATS antenna amp. harness connector and ground using an oscilloscope.

Is the inspection result normal?

YES >> Replace NATS antenna amp. Refer to SEC "Removal and Installation".

NO >> GO TO 8.

8.CHECK NATS ANTENNA AMP. OUTPUT SIGNAL CIRCUIT 2

1. Disconnect BCM connector.

2. Check continuity between NATS antenna amp. harness connector and BCM connector.

3. Check continuity between NATS antenna amp. harness connector and ground.       

Is the inspection result normal?

YES >> GO TO 9.

NO >> Repair or replace harness.

9.REPLACE BCM

1. Replace BCM. Refer to BCS "Removal and Installation".

2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.

>> Inspection End

B2196 Dongle unit

Description BCM performs ID verification between BCM and dongle unit. When verification result is OK, BCM permits cranking. ...

Other materials:

Input shaft and gear
Exploded View 1. Input shaft front bearing 2. Input shaft 3. Snap ring 4. Input shaft rear bearing 5. Adapter plate 6. Bushing 7. 5th input gear 8. 5th-reverse baulk ring 9. Synchronizer lever 10. 5th-reverse synchronizer hub 11. 5th-reverse coupling sleeve 12. Lock washer 13. Retaining pi ...

C1607, C1608 EPS Control unit
DTC Logic DTC DETECTION LOGIC        DTC CONFIRMATION PROCEDURE 1.PRECONDITIONING If "DTC CONFIRMATION PROCEDURE" has been previously conducted, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test. >> GO TO 2 ...

Categories


© 2017-2025 Copyright www.niveguide.com
0.0081