Nissan Versa (N17): P0222, P0223 TP sensor

DTC Logic

DTC DETECTION LOGIC

NOTE: If DTC P0222 or P0223 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643.

Refer to EC, "DTC Logic".

DTC No. Trouble diagnosis name DTC detecting condition Possible cause
P0222 Throttle position sensor 1 circuit low input An excessively low voltage from the TP sensor 1 is sent to ECM.
  • Harness or connectors (TP sensor 1 circuit is open or shorted.)
  • Electric throttle control actuator (TP sensor 1)
P0223 Throttle position sensor 1 circuit high input An excessively high voltage from the TP sensor 1 is sent to ECM.

DTC CONFIRMATION PROCEDURE

1.PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test.

TESTING CONDITION: Before performing the following procedure, confirm that battery voltage is more than 10 V at idle.

>> GO TO 2.

2.PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and let it idle for 1 second.
  2. Check DTC.

Is DTC detected?

YES >> Go to EC, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK GROUND CONNECTION

  1. Turn ignition switch OFF.
  2. Check ground connection E15. Refer to Ground Inspection in GI48, "Circuit Inspection".

Is the inspection result normal?

YES >> GO TO 2.

NO >> Repair or replace ground connection.

2.CHECK THROTTLE POSITION SENSOR 1 POWER SUPPLY CIRCUIT

  1. Disconnect electric throttle control actuator harness connector.
  2. Turn ignition switch ON.
  3. Check the voltage between electric throttle control actuator harness connector and ground.

Is the inspection result normal?

YES >> GO TO 3.

NO >> Repair open circuit or short to ground or short to power in harness or connectors.

3.CHECK THROTTLE POSITION SENSOR 1 GROUND CIRCUIT FOR OPEN AND SHORT

  1. Turn ignition switch OFF.
  2. Disconnect ECM harness connector.
  3. Check the continuity between electric throttle control actuator harness connector and ECM harness connector.

    4.   Also check harness for short to ground and short to power.

Is the inspection result normal?

YES >> GO TO 4.

NO >> Repair open circuit or short to ground or short to power in harness or connectors.

4.CHECK THROTTLE POSITION SENSOR 1 INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

    1.   Check the continuity between electric throttle control actuator harness connector and ECM harness connector.

    2.   Also check harness for short to ground and short to power.

Is the inspection result normal?

YES >> GO TO 5.

NO >> Repair open circuit or short to ground or short to power in harness or connectors.

5.CHECK THROTTLE POSITION SENSOR

Refer to EC, "Component Inspection".

Is the inspection result normal?

YES >> GO TO 7.

NO >> GO TO 6.

6.REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR

Replace electric throttle control actuator. Refer to EM, "Removal and Installation".

>> INSPECTION END

7.CHECK INTERMITTENT INCIDENT

Refer to GI, "Intermittent Incident".

>> INSPECTION END

Component Inspection

1.CHECK THROTTLE POSITION SENSOR

  1. Turn ignition switch OFF.
  2. Reconnect all harness connectors disconnected.
  3. Perform EC, "Work Procedure".
  4. Turn ignition switch ON.
  5. Set selector lever to D (A/T or CVT) or 1st (M/T) position.
  6. Check the voltage between ECM harness connector and ground.

Is the inspection result normal?

YES >> INSPECTION END

NO >> GO TO 2.

2.REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR

Replace electric throttle control actuator. Refer to EM, "Removal and Installation".

>> INSPECTION END

Other materials:

Front door glass
Exploded View 1. Front door panel 2. Front door lower sash (front) 3. Front door glass run 4. Front door sealing screen 5. Front door power window motor 6. Front door regulator 7. Front door glass 8. Front door lower sash (rear) 9. Regulator seal (manual window) 10. Snap pin (manual win ...

Precautions in repairing high strength steel
High Strength Steel (HSS) High strength steel is used for body panels in order to reduce vehicle weight. Accordingly, precautions in repairing automotive bodies made of high strength steel are described below: SP130 is the most commonly used HSS. Read the following precautions when repair ...

Categories


© 2017-2025 Copyright www.niveguide.com
0.0082