Nissan Versa (N17): P0500 VSS

Description

The vehicle speed signal is sent to the combination meter from the "ABS actuator and electric unit (control unit)" by CAN communication line. The combination meter then sends a signal to the ECM by CAN communication line.

DTC Logic

DTC DETECTION LOGIC

NOTE:

  • If DTC P0500 is displayed with DTC UXXXX, first perform the trouble diagnosis for DTC UXXXX.
  • If DTC P0500 is displayed with DTC P0607, first perform the trouble diagnosis for DTC P0607. Refer to EC, "DTC Logic".
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
P0500 Vehicle speed sensor The almost 0 km/h (0 MPH) of vehicle speed signal is sent to ECM even when vehicle is being driven.
  • Harness or connectors (The CAN communication line is open or shorted)
  • Harness or connectors (The vehicle speed signal circuit is open or shorted)
  • Combination meter
  • ABS actuator and electric unit (control unit)

DTC CONFIRMATION PROCEDURE

1.INSPECTION START

Do you have CONSULT?

YES >> GO TO 2.

NO >> GO TO 5.

2.PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.
  2. Turn ignition switch ON.
  3. Turn ignition switch OFF and wait at least 10 seconds.

>> GO TO 3.

3.CHECK VEHICLE SPEED SENSOR FUNCTION

NOTE: This procedure may be conducted with the drive wheels lifted in the shop or by driving the vehicle. If a road test is expected to be easier, it is unnecessary to lift the vehicle.

With CONSULT

  1. Start engine.
  2. Read "VHCL SPEED SE" in "DATA MONITOR" mode with CONSULT. The vehicle speed on CONSULT should exceed 10 km/h (6 mph) when rotating wheels with suitable gear position.

Is the inspection result normal?

YES >> GO TO 4.

NO >> Go to EC, "Diagnosis Procedure".

4.PERFORM DTC CONFIRMATION PROCEDURE

  1. Select "DATA MONITOR" mode with CONSULT.
  2. Warm engine up to normal operating temperature.
  3. Maintain the following conditions for at least 60 consecutive seconds.

CAUTION: Always drive vehicle at a safe speed.                       

    4.   Check 1st trip DTC.

Is 1st trip DTC detected?

YES >> Go to EC, "Diagnosis Procedure".

NO >> INSPECTION END

5.PERFORM COMPONENT FUNCTION CHECK

Perform component function check. Refer to EC, "Component Function Check".

Use component function check to check the overall function of the vehicle speed signal circuit. During this check, a 1st trip DTC might not be confirmed.

Is the inspection result normal?

YES >> INSPECTION END

NO >> Go to EC, "Diagnosis Procedure".

Component Function Check

1.PERFORM COMPONENT FUNCTION CHECK

With GST

  1. Lift up drive wheels.
  2. Start engine.
  3. Read vehicle speed signal in Service $01 with GST.

    The vehicle speed signal on GST should be able to exceed 10 km/h (6 MPH) when rotating wheels with suitable gear position.

Is the inspection result normal?

YES >> INSPECTION END

NO >> Go to EC, "Diagnosis Procedure".

Diagnosis Procedure

1.CHECK DTC WITH ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)

Check DTC with ABS actuator and electric unit (control unit). Refer to BRC, "DTC Index".

Is the inspection result normal?

YES >> GO TO 2.

NO >> Repair or replace.

2.CHECK DTC WITH COMBINATION METER

Check DTC with combination meter. Refer to MWI, "DTC Index" (TYPE A) or MWI, "DTC Index" (TYPE B).

>> INSPECTION END

P0506 ISC system

Description The ECM controls the engine idle speed to a specified level through the fine adjustment of the air, which is let into the intake manifold, by operating the electric throttle control ac ...

Other materials:

Spark plugs
Replacing spark plugs Platinum-tipped spark plugs It is not necessary to replace platinum-tipped A spark plugs as frequently as conventional type spark plugs because they last much longer. Follow the maintenance log shown in the Maintenance and Schedules section of this manual. Do not ser ...

Preparation
Special Service Tools The actual shapes of KentMoore tools may differ from those of special service tools illustrated here. Tool number (KentMoore No.) Tool name Description KV10111100 (J37228) Seal cutter   Removing oil pan (lower and upper) etc. ...

Categories


© 2017-2025 Copyright www.niveguide.com
0.007