Description
This malfunction is detected when the A/T does not shift into 2GR position as instructed by TCM. This is not only caused by electrical malfunction (circuits open or shorted) but by mechanical malfunction such as control valve sticking, improper solenoid valve operation, etc.
DTC Logic
DTC DETECTION LOGIC
DTC | Trouble diagnosis name | DTC detection condition | Possible causes |
P074A | Unable to Engage Gear 2 | Under the following diagnosis
conditions, the gear ratio is
3.033 or more continuously for
2 seconds or more. - Diagnosis condition - Shifting is not in progress. - Input speed: 300 rpm or more - Output speed: 300 rpm or more - Engine speed: (Input speed - 50 rpm) or more - Selector lever: 2 position - Gear: 2GR - Throttle position: 0.7/8.0 or more |
- Low clutch solenoid valve - Control valve assembly |
DTC CONFIRMATION PROCEDURE
CAUTION:
1.PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT
NOTE: "2ND GR FNCTN P0731" can be used in this diagnosis.
Selector lever : 2 position
Gear : 2GR
Accelerator pedal position : 0.7/8 or more
Vehicle speed : 5 km/h (4 MPH) or more
3. Keep the current driving status for 2 seconds or more if CONSULT screen changes from "OUT OFCONDITION" to "TESTING".
CAUTION: When "TESTING" is not indicated on CONSULT for a long time, check "Self Diagnostic Results" in "TRANSMISSION". When a DTC other than "P074A" is detected, check the DTC. Refer to TM, "DTC Index".
With GST
1. Drive vehicle and maintain the following conditions for 2 seconds or more.
Selector lever : 2 position
Gear : 2GR
Accelerator pedal position : 0.7/8 or more
Vehicle speed : 5 km/h (4 MPH) or more
2. Check the first trip DTC.
Is "OUT OF CONDITION", "STOP VEHICLE", or "COMPLETED RESULT NG" displayed? / Is "P074A" detected?
YES-1 (OUT OF CONDITION.)>>Perform "step 2" again.
YES-2 (STOP VEHICLE.)>>GO TO 3.
YES-3 (COMPLETED RESULT NG)>>Go to TM, "Diagnosis Procedure".
YES-4 ("P074A" is detected.)>>Go to TM, "Diagnosis Procedure".
NO >> GO TO 3.
3.CHECK SYMPTOM
>> INSPECTION END
Diagnosis Procedure
1.MALFUNCTION CAUSE SIMULATION TEST
Refer to GI, "Intermittent Incident".
Is the check result normal?
YES >> Replace the transaxle assembly. Refer to TM, "Removal and Installation".
NO >> Repair or replace the malfunctioning parts.
Description This DTC is detected when the torque converter clutch solenoid valve is electrically normal but the torque converter clutch does not engage. This is not due to an electrical malfunctio ...
Description This malfunction is detected when the A/T does not shift into 3GR position as instructed by TCM. This is not only caused by electrical malfunction (circuits open or shorted) but by m ...
Windows
Power windows (if so equipped)
WARNING
Make sure that all passengers have
their hands, etc. inside the vehicle while
it is in motion and before closing the
windows. Use the window lock switch to
prevent unexpected use of the power
windows
To help avoid risk of injury or death
thr ...
Event Data Recorders (EDR)
This vehicle is equipped with an Event Data Recorder
(EDR). The main purpose of an EDR is to
record, in certain crash or near crash-like situations,
such as an air bag deployment or hitting a
road obstacle, data that will assist in understanding
how a vehicle's systems performed. The EDR
is de ...