Toyota
Nissan Versa
 Sedan Service Manual
Engine » Engine control system (EC) » How to erase permanent DTC
Work Procedure (Group B)

Work Procedure (Group B)

*1: When the same malfunction is detected in two consecutive trips, MIL will illuminate.

*2: After experiencing driving pattern B and D, permanent DTC is erased.

*3: Indication does not change unless the ignition switch is turned from ON to OFF twice even after experiencing driving pattern B or D.

NOTE: Drive the vehicle according to only driving patterns indicating "INCMP" in driving patterns B and D on the "PERMANENT DTC STATUS" screen.

1.CHECK DTC

Check DTC.

Is any DTC detected?

YES >> Repair malfunction(s) and erase DTC.

NO >> GO TO 2.

2.CHECK PERMANENT DTC

With CONSULT

  1. Turn ignition switch OFF and wait at least 10 seconds.
  2. Turn ignition switch ON.
  3. Turn ignition switch OFF and wait at least 10 seconds.
  4. Turn ignition switch ON.
  5. Select "PERMANENT DTC STATUS" mode with CONSULT.

With GST

  1. Turn ignition switch OFF and wait at least 10 seconds.
  2. Turn ignition switch ON.
  3. Turn ignition switch OFF and wait at least 10 seconds.
  4. Turn ignition switch ON.
  5. Select Service $0A with GST.

Is any permanent DTC detected?

YES >> GO TO 3.

NO >> END

3.DRIVE DRIVING PATTERN B

CAUTION:

  • Always drive at a safe speed.
  • Never erase selfdiagnosis results.
  • If selfdiagnosis results are erased during the trip of driving pattern B or D, the counter of driving pattern B and D is reset.

With CONSULT

  1. Start engine and warm it up to normal operating temperature.
  2. Use "PERMANENT DTC WORK SUPPORT" mode with CONSULT to drive the vehicle according to driving pattern B.

With GST

  1. Start engine and warm it up to normal operating temperature.
  2. Drive the vehicle according to driving pattern B.

>> GO TO 4.

4.CHECK PERMANENT DTC

With CONSULT

  1. Turn ignition switch OFF and wait at least 10 seconds.
  2. Turn ignition switch ON.
  3. Turn ignition switch OFF and wait at least 10 seconds.
  4. Turn ignition switch ON.
  5. Select "PERMANENT DTC STATUS" mode with CONSULT.

With GST

  1. Turn ignition switch OFF and wait at least 10 seconds.
  2. Turn ignition switch ON.
  3. Turn ignition switch OFF and wait at least 10 seconds.
  4. Turn ignition switch ON.
  5. Select Service $0A with GST.

Is any permanent DTC detected?

YES >> GO TO 5.

NO >> END

5.DRIVE DRIVING PATTERN D

CAUTION:

  • Always drive at a safe speed.
  • Never erase selfdiagnosis results.
  • If selfdiagnosis results are erased during the trip of driving pattern B or D, the counter of driving pattern B and D is reset.

Drive the vehicle according to driving pattern D. Refer to EC, "Work Procedure (Group B)".

>> GO TO 6.

6.CHECK PERMANENT DTC

With CONSULT

  1. Turn ignition switch OFF and wait at least 10 seconds.
  2. Turn ignition switch ON.
  3. Turn ignition switch OFF and wait at least 10 seconds.
  4. Turn ignition switch ON.
  5. Select "PERMANENT DTC STATUS" mode with CONSULT.

With GST

  1. Turn ignition switch OFF and wait at least 10 seconds.
  2. Turn ignition switch ON.
  3. Turn ignition switch OFF and wait at least 10 seconds.
  4. Turn ignition switch ON.
  5. Select Service $0A with GST.

Is any permanent DTC detected?

YES >> GO TO 1.

NO >> END

    More about «How to erase permanent DTC»:

    Description

    Work Procedure (Group A)

    Work Procedure (Group B)

    Nissan Versa Sedan Service Manual / Engine / Engine control system (EC) / How to erase permanent DTC / Work Procedure (Group B)

    Nissan Versa Sedan Service Manual

    Categories


    © 2017-2019 Copyright www.niveguide.com