Toyota
Nissan Versa
 Sedan Service Manual
Brakes » Brake control system (BRC)
Adjustment of steering angle sensor neutral position

Description

Refer to the table below to determine if adjustment of steering angle sensor neutral position is required.

Description

Work Procedure

ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION

CAUTION: To adjust neutral position of steering angle sensor, make sure to use CONSULT.

(Adjustment cannot be done without CONSULT).

1.ALIGN THE VEHICLE STATUS

Stop vehicle with front wheels in straight-ahead position.

>> GO TO 2

2.PERFORM THE NEUTRAL POSITION ADJUSTMENT FOR THE STEERING ANGLE SENSOR

  1. On the CONSULT screen, touch "WORK SUPPORT" and "ST ANG SEN ADJUSTMENT" in order.
  2. Touch "START".CAUTION:Do not touch steering wheel while adjusting steering angle sensor.
  3. After approximately 10 seconds, touch "END".

    NOTE: After approximately 60 seconds, it ends automatically.

  4. Turn ignition switch OFF, then turn it ON again.

    CAUTION: Be sure to perform above operation.

>> GO TO 3

3.CHECK DATA MONITOR

  1. Run vehicle with front wheels in straight-ahead position, then stop.
  2. Select "DATA MONITOR". Then make sure "STR ANGLE SIG" is within 0+-2.5.

Is the steering angle within the specified range?

YES >> GO TO 4

NO >> Perform the neutral position adjustment for the steering angle sensor again, GO TO 1

4.ERASE THE SELF-DIAGNOSIS MEMORY

Erase the self-diagnosis memory of the ABS actuator and electric unit (control unit) and ECM.

  • ABS actuator and electric unit (control unit): Refer to BRC "CONSULT Function (ABS)".
  • ECM: Refer to EC "CONSULT Function".

Are the memories erased?

YES >> Inspection End

NO >> Check the items indicated by the self-diagnosis.

DTC/CIRCUIT DIAGNOSIS

    More about «Brake control system (BRC)»:

    Precautions

    Component parts

    VDC/TCS/ABS

    Diagnosis system [abs actuator and electric unit (control unit)]

    ABS Actuator and electric unit (control unit)

    Diagnosis and repair work flow

    Adjustment of steering angle sensor neutral position

    C1101, C1102, C1103, C1104 Wheel sensor

    C1105, C1106, C1107, C1108 Wheel sensor

    C1109 Power and ground system

    C1110, C1153, C1170 ABS Actuator and electric unit (control unit)

    C1111 Pump motor

    C1115 ABS Sensor [abnormal signal]

    C1116 Stop lamp switch

    C1120, C1122, C1124, C1126 ABS In valve system

    C1121, C1123, C1125, C1127 ABS Out valve system

    C1130 Engine signal

    C1140 Actuator relay system

    C1142 Press sensor

    C1143 Steering angle sensor

    C1144 Incomplete steering angle sensor adjustment

    C1145, C1146 Yaw rate/side/decel g sensor

    C1155 BR Fluid level low

    C1164, C1165, C1166, C1167 CV/SV System

    U1000 CAN Comm circuit

    U1002 System comm (CAN)

    Parking brake switch

    VDC OFF Switch

    ABS Warning lamp

    Brake warning lamp

    VDC OFF Indicator lamp

    Slip indicator lamp

    VDC/TCS/ABS

    Excessive ABS Function operation frequency

    Unexpected pedal reaction

    The braking distance is long

    Pedal vibration or ABS operation sound occurs

    Vehicle jerks during VDC/TCS/ABS control

    Wheel sensor

    Sensor rotor

    ABS Actuator and electric unit (control unit)

    Nissan Versa Sedan Service Manual / Brakes / Brake control system (BRC) / Adjustment of steering angle sensor neutral position

    Nissan Versa Sedan Service Manual

    Categories


    © 2017-2024 Copyright www.niveguide.com