Toyota
Nissan Versa
 Sedan Service Manual
Engine » Engine control system (EC) » P0101 MAF sensor
Component Inspection

1.CHECK MASS AIR FLOW SENSORI

With CONSULT

  1. Turn ignition switch OFF.
  2. Reconnect all harness connectors disconnected.
  3. Start engine and warm it up to normal operating temperature.
  4. Connect CONSULT and select "DATA MONITOR" mode of "ENGINE".
  5. Select "MAS A/F SEB1" and check indication.

CHECK MASS AIR FLOW SENSORI

*: Check for linear voltage rise in response to engine being increased to about 4,000 rpm.

Without CONSULT

  1. Turn ignition switch OFF.
  2. Reconnect all harness connectors disconnected.
  3. Start engine and warm it up to normal operating temperature.
  4. Check the voltage between ECM harness connector and ground.

CHECK MASS AIR FLOW SENSORI

*: Check for linear voltage rise in response to engine being increased to about 4,000 rpm.

Is the inspection result normal?

YES >> INSPECTION END

NO >> GO TO 2.

2.CHECK FOR THE CAUSE OF UNEVEN AIR FLOW THROUGH MASS AIR FLOW SENSOR

  1. Turn ignition switch OFF.
  2. Check for the cause of uneven air flow through mass air flow sensor. Refer to the following.
  • Crushed air ducts
  • Malfunctioning seal of air cleaner element
  • Uneven dirt of air cleaner element
  • Improper specification of intake air system parts

Is the inspection result normal?

YES >> GO TO 4.

NO >> GO TO 3.

3.CHECK MASS AIR FLOW SENSORII

With CONSULT

  1. Repair or replace malfunctioning part.
  2. Start engine and warm it up to normal operating temperature.
  3. Connect CONSULT and select "DATA MONITOR" mode of "ENGINE".
  4. Select "MAS A/F SEB1" and check indication.

CHECK MASS AIR FLOW SENSORII

*: Check for linear voltage rise in response to engine being increased to about 4,000 rpm.

Without CONSULT

  1. Repair or replace malfunctioning part.
  2. Start engine and warm it up to normal operating temperature.
  3. Check the voltage between ECM harness connector and ground.

CHECK MASS AIR FLOW SENSORII

*: Check for linear voltage rise in response to engine being increased to about 4,000 rpm.

Is the inspection result normal?

YES >> INSPECTION END

NO >> GO TO 4.

4.CHECK MASS AIR FLOW SENSORIII

With CONSULT

  1. Turn ignition switch OFF.
  2. Disconnect mass air flow sensor harness connector and reconnect it again.
  3. Start engine and warm it up to normal operating temperature.
  4. Connect CONSULT and select "DATA MONITOR" mode of "ENGINE".
  5. Select "MAS A/F SEB1" and check indication.

CHECK MASS AIR FLOW SENSORIII

*: Check for linear voltage rise in response to engine being increased to about 4,000 rpm.

Without CONSULT

  1. Turn ignition switch OFF.
  2. Disconnect mass air flow sensor harness connector and reconnect it again.
  3. Start engine and warm it up to normal operating temperature.
  4. Check the voltage between ECM harness connector and ground.

CHECK MASS AIR FLOW SENSORIII

*: Check for linear voltage rise in response to engine being increased to about 4,000 rpm.

Is the inspection result normal?

YES >> INSPECTION END

NO >> Clean or replace mass air flow sensor. Refer to EM, "Removal and Installation".

    More about «P0101 MAF sensor»:

    DTC Logic

    Diagnosis Procedure

    Component Inspection

    Nissan Versa Sedan Service Manual / Engine / Engine control system (EC) / P0101 MAF sensor / Component Inspection

    Nissan Versa Sedan Service Manual

    Categories


    © 2017-2024 Copyright www.niveguide.com