Nissan Versa (N17): P1554 battery current sensor

DTC Logic

DTC DETECTION LOGIC

DTC No. Trouble diagnosis DTC detecting condition Possible cause
P1554 Battery current sensor performance The output voltage of the battery current sensor is lower than the specified value while the battery voltage is high enough.
  • Harness or connectors (Battery current sensor circuit is open or shorted.) (APP sensor 2 circuit is open or shorted.) (EVAP control system pressure sensor circuit is shorted.) [Crankshaft position sensor (POS) circuit is shorted.] (Refrigerant pressure sensor circuit is shorted.)
  • Battery current sensor
  • Accelerator pedal position sensor (APP sensor 2)
  • EVAP control system pressure sensor
  • Crankshaft position sensor (POS)
  • Refrigerant pressure sensor

DTC CONFIRMATION PROCEDURE

1.PERFORM COMPONENT FUNCTION CHECK

Perform component function check. Refer to EC, "Component Function Check".

NOTE: Use component function check to check the overall function of the battery current sensor circuit. During this check, a 1st trip DTC might not be confirmed.

Is the inspection result normal?

YES >> INSPECTION END

NO >> Go to EC, "Diagnosis Procedure".

Component Function Check

1.PRECONDITIONING

TESTING CONDITION:

  • Before performing the following procedure, confirm that battery voltage is more than 12.8 V at idle.
  • Before performing the following procedure, confirm that all load switches and A/C switch are turned OFF.

>> GO TO 2.

2.PERFORM COMPONENT FUNCTION CHECK

With CONSULT

  1. Start engine and let it idle.
  2. Select "BAT CUR SEN" in "DATA MONITOR" mode with CONSULT.
  3. Check "BAT CUR SEN" indication for 10 seconds.

    "BAT CUR SEN" should be above 2,300 mV at least once.

Without CONSULT

  1. Start engine and let it idle.
  2. Check the voltage between ECM harness connector terminals as per the following.

Is the inspection result normal?

YES >> INSPECTION END

NO >> Go to EC, "Diagnosis Procedure"

Diagnosis Procedure

1.CHECK GROUND CONNECTION

  1. Turn ignition switch OFF.
  2. Check ground connection E15. Refer to Ground Inspection in GI, "Circuit Inspection".

Is the inspection result normal?

YES >> GO TO 2.

NO >> Repair or replace ground connection.

2.CHECK BATTERY CURRENT SENSOR POWER SUPPLY

  1. Disconnect battery current sensor harness connector.
  2. Turn ignition switch ON.
  3. Check the voltage between battery current sensor harness connector and ground. 

Is the inspection result normal?

YES >> GO TO 4.

NO >> GO TO 3.

3.CHECK BATTERY CURRENT SENSOR POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.
  2. Disconnect ECM harness connector.
  3. Check the continuity between battery current sensor harness connector and ECM harness connector.
  4. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES >> Check intermittent incident. Refer to GI, "Intermittent Incident".

NO >> Repair or replace error-detected parts.

4.CHECK BATTERY CURRENT SENSOR GROUND CIRCUIT FOR OPEN AND SHORT

  1. Turn ignition switch OFF.
  2. Disconnect ECM harness connector.
  3. Check the continuity between battery current sensor harness connector and ECM harness connector.
  4. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES >> GO TO 5.

NO >> Repair or replace error-detected parts.

5.CHECK BATTERY CURRENT SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

  1. Check the continuity between battery current sensor harness connector and ECM harness connector.
  2. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES >> GO TO 6.

NO >> Repair or replace error-detected parts.

6.CHECK BATTERY CURRENT SENSOR

Check battery current sensor. Refer to EC, "Component Inspection".

Is the inspection result normal?

YES >> Check intermittent incident. Refer to GI, "Intermittent Incident".

NO >> Replace battery negative cable assembly.

Component Inspection

1.CHECK BATTERY CURRENT SENSOR

  1. Turn ignition switch OFF.
  2. Reconnect harness connectors disconnected.
  3. Disconnect battery negative cable (1).
  4. Install jumper cable (A) between battery negative terminal and body ground. : To body ground
  5. Turn ignition switch ON.
  6. Check the voltage between ECM harness connector terminals as per the following.                                       Before measuring the terminal voltage, confirm that the battery is fully charged. Refer to PG, "How to Handle Battery".

 CHECK BATTERY CURRENT SENSOR

Is the inspection result normal?

YES >> INSPECTION END

NO >> Replace battery negative cable assembly.

Other materials:

5Th main gear assembly
Removal and Installation REMOVAL Move the shift selector to the 3rd gear position. Disconnect the shifter cable and the selector cable from shifter lever A and selector lever. Refer to TM, "Removal and Installation". CAUTION: Do not move shifter lever A and selector leve ...

Insufficient heating
Description Symptom Insufficient heating No warm air comes out. (Air flow volume is normal.) Diagnosis Procedure NOTE: Perform self-diagnosis with CONSULT before performing symptom diagnosis. If any malfunction result or DTC is detected, perform the corresponding diagnosis. 1.CHECK ...

Categories


© 2017-2025 Copyright www.niveguide.com
0.0089