Nissan Versa

 Sedan Service Manual

Maintenance (MA) » Chassis and body maintenance
CVT Fluid

CVT FLUID : Inspection

FLUID LEAKAGE

• Check transaxle surrounding area (oil seal and plug etc.) for fluid leakage.
• If anything is found, repair or replace damaged parts and adjust CVT fluid level. Refer to TM "Adjustment".

CVT FLUID : Replacement

CVT fluid : Refer to TM "General Specification".

Fluid capacity : Refer to TM "General Specification".

CAUTION:

• Use only Genuine NISSAN CVT Fluid NS-3. Using transmission fluid other than Genuine NISSAN CVT Fluid NS-3 will damage the CVT, which is not covered by the (NISSAN new vehicle limited) warranty.
• Always use shop paper. Do not use shop cloth.
• Replace a drain plug gasket with new ones at the final stage of the operation when installing.
• Use caution when looking into the drain hole as there is a risk of dripping fluid entering the eye.
• After replacement, always perform CVT fluid leakage check.

1. Select "Data Monitor" in "TRANSMISSION" using CONSULT.

2. Select "FLUID TEMP" and confirm that the CVT fluid temperature is 40C (104F) or less.

3. Check that the selector lever is in the "P" position, then completely engage the parking brake.

4. Lift up the vehicle.

5. Remove the drain plug and overflow tube and drain the CVT fluid from the oil pan. TM "Removal and Installation".

6. Install the charging pipe set (KV311039S0) (A) into the drain hole.

CAUTION: Tighten the charging pipe by hand.

7. Install the ATF changer hose (B) to the charging pipe.

CAUTION: Press the ATF changer hose all the way onto the charging pipe until it stops.

8. Fill approximately 3 liter (3-1/8 US qt, 2-5/8 lmp qt) of the CVT fluid.

9. Remove the ATF changer hose and charging pipe, then install the drain plug.

NOTE: Perform this work quickly because CVT fluid leaks.

10. Lift down the vehicle.

11. Start the engine.

12. While depressing the brake pedal, shift the selector lever to the entire position from "P" to "L", and shift it to the "P" position.

NOTE: Hold the lever at each position for 5 seconds.

13. Check that the CONSULT "Data monitor" in "FLUID TEMP" is 35C (95F) to 45C (113F).

14. Stop the engine.

15. Lift up the vehicle.

16. Remove the drain plug, and then drain CVT fluid from oil pan.

17. Repeat steps 6 to 16 (one time).

18. Install the overflow tube. Refer to TM "Removal and Installation".

CAUTION: Be sure to tighten to the specified torque. If it is not tightened to the specified torque, the tube may be damaged.

19. Install the charging pipe set (KV311039S0) (A) into the drain hole.

CAUTION: Tighten the charging pipe by hand.

20. Install the ATF changer hose (B) to the charging pipe.

CAUTION: Press the ATF changer hose all the way onto the charging pipe until it stops.

21. Fill approximately 3 liter (3-1/8 US qt, 2-5/8 lmp qt) of the CVT fluid.

22. Remove the ATF changer hose and charging pipe, then install the drain plug.

NOTE: Perform this work quickly because CVT fluid leaks.

23. Lift down the vehicle.

24. Start the engine.

25. While depressing the brake pedal, shift the selector lever to the entire position from "P" to "L", and shift it to the "P" position.

NOTE: Hold the lever at each position for 5 seconds.

26. Check that the CONSULT "Data monitor" in "FLUID TEMP" is 35C (95F) to 45C (113F).

27. Lift up the vehicle.

28. Remove the drain plug and confirm that the CVT fluid is drained from the overflow tube.

CAUTION: Perform this work with the vehicle idling.

NOTE: If the CVT fluid is not drained, refer to "Adjustment" and refill with the CVT fluid.

29. When the flow of CVT fluid slows to a drip, tighten the drain plug to the specified torque. TM "Removal and Installation".

CAUTION: Do not reuse drain plug gasket.

30. Lift down the vehicle.

31. Select "Work Support" in "TRANSMISSION" using CONSULT.

32. Select "CONFORM CVTF DETERIORTN".

33. Select "Erase".

34. Stop the engine.

CVT FLUID : Adjustment

CVT fluid : Refer to TM "General Specification".

Fluid capacity : Refer to TM "General Specification".

CAUTION:

• Use only Genuine NISSAN CVT Fluid NS-3. Using transmission fluid other than Genuine NISSAN CVT Fluid NS-3 will damage the CVT, which is not covered by the (NISSAN new vehicle limited) warranty.
• During adjustment of the CVT fluid level, check CONSULT so that the oil temperature may be maintained from 35 to 45C (95 to 113F).
• Use caution when looking into the drain hole as there is a risk of dripping fluid entering the eye.

1. Check that the selector lever is in the "P" position, then completely engage the parking brake.

2. Start the engine.

3. Adjust the CVT fluid temperature to be approximately 40C (104F).

NOTE: The CVT fluid is largely affected by temperature. Therefore be sure to use CONSULT and check the "FLUID TEMP" under "TRANSMISSION" in "Data Monitor" while adjusting.

4. While depressing the brake pedal, shift the selector lever to the entire position from "P" to "L", and shift it to the "P" position.

NOTE: Hold the lever at each position for 5 seconds.

5. Lift up the vehicle.

6. Check that there is no CVT fluid leakage.

7. Remove the drain plug. Refer to TM "Removal and Installation".

8. Install the charging pipe set (KV311039S0) (A) into the drain plug hole.

CAUTION: Tighten the charging pipe by hand.

9. Install the ATF changer hose (B) to the charging pipe.

CAUTION: Press the ATF changer hose all the way onto the charging pipe until it stops.

10. Fill approximately 0.5 liter (1/2 US qt, 1/2 lmp qt) of the CVT fluid.

11. Remove the ATF changer hose from the charging pipe, and check that the CVT fluid drains out from the charging pipe. If it does not drain out, perform charging again.

CAUTION: Perform this work with the vehicle idling.

12. When the flow of CVT fluid slows to a drip, remove the charging pipe from the oil pan.

13. Tighten the drain plug to the specified torque. Refer to TM "Removal and Installation".

CAUTION: Do not reuse drain plug gasket.

14. Lift down the vehicle.

15. Stop the engine.

Exhaust system

CVT Fluid

A/T Fluid

Clutch fluid

M/T Oil

Road wheel

Brake fluid level and leaks

Brake lines and cables

Brake fluid

Disc brake

Drum brake

Steering gear and linkage

Axle and suspension parts

Seat belt, buckles, retractors, anchors and adjusters