Toyota
Nissan Versa
 Sedan Service Manual
Maintenance (MA) » Engine maintenance
Drive belt

DRIVE BELT : Exploded View

DRIVE BELT : Exploded View

1. Generator 2. Water pump 3. Crankshaft pulley 4. A/C compressor (with A/C models) Idler pulley (without A/C models) 5. Idler pulley 6. Drive belt

DRIVE BELT : Inspection

  • Inspection should be done only when engine is cold or over 30 minutes after the engine is stopped.

(1) : Generator

(2) : Water pump

(3) : Crankshaft pulley

(4) : A/C compressor (with A/C models) : Idler pulley (without A/C models)

(5) : Idler pulley

(6) : Drive belt

  • Visually check belt for wear, damage, and cracks on inside and edges.
  • Turn crankshaft pulley clockwise twice, and check that the tension on all pulleys equalizes before testing.
  • When measuring deflection, apply 98.1 N (10 kg, 22 lb) at the ( ) marked point.
  • Measure the belt tension and frequency with acoustic tension gauge at the ( ) marked point.

DRIVE BELT : Inspection

CAUTION:

  • When the tension and frequency are measured, the acoustic tension gauge should be used.
  • When checking immediately after installation, first adjust it to the specified value. Then, after turning crankshaft two turns or more, readjust to the specified value to avoid variation in deflection between pulleys.

Belt deflection/belt tension and frequency : Refer to EM "Drive Belt".

DRIVE BELT : Adjustment            

CAUTION:

  • When belt is replaced with new one, adjust belt tension to the value for "New belt," because new belt will not fully seat in the pulley groove.
  • When tension of the belt being used exceeds "Limit," adjust it to the value for "After adjusted."
  • When installing a belt, check it is correctly engaged with the pulley groove.
  • Do not allow oil or engine coolant to get on the belt.
  • Do not twist or bend the belt strongly.

1. Remove the fender protector (RH) front side clip. Refer to EXT "Removal and Installation".

2. Tighten lock nut (A) temporarily to the following torque.

Lock nut (A) (Temporary tightening) : 4.4 N*m (0.45 kg-m, 39 in-lb)

(1) : Generator

(2) : Water pump

(3) : Crankshaft pulley

(4) : A/C compressor (with A/C models) : Idler pulley (without A/C models)

(5) : Idler pulley

(6) : Drive belt

(B) : Adjusting bolt

DRIVE BELT : Adjustment

3. Adjust the belt tension by turning the adjusting bolt. Refer to EM "Drive Belt".

CAUTION:

  • When checking immediately after installation, first adjust it to the specified value. Then, after turning crankshaft two turns or more, readjust to the specified value to avoid variation in deflection between pulleys.
  • When the tension adjustment is performed, the lock nut should be in the condition at Step 2. If the tension adjustment is performed when the lock nut is loosened more than the temporary tightening, the idler pulley tilts and the correct tension adjustment cannot be performed.

4. Tighten the lock nut to final tightening specification.

Lock nut (Final tightening) : 34.8 N*m (3.5 kg-m, 26 ft-lb)

    More about «Engine maintenance»:

    Drive belt

    Engine coolant

    Fuel lines

    Air cleaner filter

    Engine oil

    Oil filter

    Spark plug

    Nissan Versa Sedan Service Manual / Maintenance (MA) / Engine maintenance / Drive belt

    Nissan Versa Sedan Service Manual

    Categories


    © 2017-2024 Copyright www.niveguide.com