Toyota
Nissan Versa
 Sedan Service Manual
Engine » Engine control system (EC) » Precaution
General Precautions

  • Always use a 12 volt battery as power source.
  • Do not attempt to disconnect battery cables while engine is running.
  • Before connecting or disconnecting the ECM harness connector, turn ignition switch OFF and disconnect negative battery cable. Failure to do so may damage the ECM because battery voltage is applied to ECM even if ignition switch is turned OFF.
  • Before removing parts, turn ignition switch OFF and then disconnect battery ground cable.

General Precautions

  • Do not disassemble ECM.
  • If a battery cable is disconnected, the memory will return to the ECM value.

    The ECM will now start to selfcontrol at its initial value. So, engine operation can vary slightly in this case. However, this is not an indication of a malfunction. Do not replace parts because of a slight variation.

  • If the battery is disconnected, the following emissionrelated diagnostic information will be lost within 24 hours.
  • Diagnostic trouble codes
  • 1st trip diagnostic trouble codes
  • Freeze frame data
  • 1st trip freeze frame data
  • System readiness test (SRT) codes
  • Test values

General Precautions

  • When connecting ECM harness connector (1), fasten (B) it securely with a lever as far as it will go as shown in the figure.
  • ECM (2)
  • Loosen (A)

General Precautions

  • When connecting or disconnecting pin connectors into or from ECM, take care not to damage pin terminals (bend or break).

    Make sure that there are not any bends or breaks on ECM pin terminal, when connecting pin connectors.

  • Securely connect ECM harness connectors.

    A poor connection can cause an extremely high (surge) voltage to develop in coil and condenser, thus resulting in damage to ICs.

  • Keep engine control system harness at least 10 cm (4 in) away from adjacent harness, to prevent engine control system malfunctions due to receiving external noise, degraded operation of ICs, etc.

General Precautions

  • Keep engine control system parts and harness dry.
  • Before replacing ECM, perform ECM Terminals and Reference Value inspection and make sure ECM functions properly.
  • Handle mass air flow sensor carefully to avoid damage.
  • Do not clean mass air flow sensor with any type of detergent.
  • Do not disassemble electric throttle control actuator.
  • Even a slight leak in the air intake system can cause serious incidents.
  • Do not shock or jar the camshaft position sensor (PHASE), crankshaft position sensor (POS).

General Precautions

  • After performing each TROUBLE DIAGNOSIS, perform DTC CONFIRMATION PROCEDURE or Component Function Check. The DTC should not be displayed in the DTC Confirmation Procedure if the repair is completed. The Component Function Check should be a good result if the repair is completed.

General Precautions

  • When measuring ECM signals with a circuit tester, never allow the two tester probes to contact.

    Accidental contact of probes will cause a short circuit and damage the ECM power transistor.

General Precautions

  • Do not operate fuel pump when there is no fuel in lines.
  • Tighten fuel hose clamps to the specified torque.
  • Do not depress accelerator pedal when starting.
  • Immediately after starting, do not rev up engine unnecessarily.
  • Do not rev up engine just prior to shutdown.

General Precautions

  • When installing C.B. ham radio or a mobile phone, be sure to observe the following as it may adversely affect electronic control systems depending on installation location.
  • Keep the antenna as far as possible from the electronic control units.
  • Keep the antenna feeder line more than 20 cm (8 in) away from the harness of electronic controls.

    Do not let them run parallel for a long distance.

  • Adjust the antenna and feeder line so that the standingwave ratio can be kept smaller.
  • Be sure to ground the radio to vehicle body.

General Precautions

PREPARATION

Special Service Tools

NOTE:

The actual shapes of KentMoore tools may differ from those of special service tools illustrated here.

Tool number (KentMoore No.) Tool name Description
(J44321) Fuel pressure gauge kit          Checks fuel pressure
(J443216) Fuel pressure adapter        Connects fuel pressure gauge to quick connector type fuel lines.
KV10118400 Fuel tube adapter           Measuring fuel pressure
KV10120000 Fuel tube adapter    

Commercial Service Tools

Tool name (KentMoore No.) Description
Leak detector i.e.: (J41416)                         Locates the EVAP leak
EVAP service port adapter i.e.: (J41413OBD)                    Applies positive pressure through EVAP service port
Fuel filler cap adapter i.e.: (MLR8382)              Checks fuel tank vacuum relief valve opening pressure
Socket wrench                           Removes and installs engine coolant temperature sensor
Oxygen sensor thread cleaner i.e.: (J4389718), (J4389712)  Reconditioning the exhaust system threads before installing a new oxygen sensor. Use with antiseize lubricant shown below.

a: 18 mm diameter with pitch 1.5 mm for Zirconia Oxygen Sensor b: 12 mm diameter with pitch 1.25 mm for Titania Oxygen Sensor

Antiseize lubricant i.e.: (PermatexTM 133AR or equivalent meeting MIL specification MILA907)                                         Lubricating oxygen sensor thread cleaning tool when reconditioning exhaust system threads.
    More about «Precaution»:

    Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRETENSIONER"

    On Board Diagnostic (OBD) System of Engine and A/T or CVT

    General Precautions

    Nissan Versa Sedan Service Manual / Engine / Engine control system (EC) / Precaution / General Precautions

    Nissan Versa Sedan Service Manual

    Categories


    © 2017-2024 Copyright www.niveguide.com