Nissan Versa (N17): P2859 Clutch A pressure

Nissan Versa 2nd generation (N17) Service Manual / Transmission & driveline / Transaxle & transmission (TM) / P2859 Clutch A pressure

DTC Logic

DTC DETECTION LOGIC

DTC Trouble diagnosis name DTC detection condition Possible causes
P2859 Clutch A pressuren disengagement performance The detection conditions continuously for 200 msec or more under the following diagnosis conditions:

- Diagnosis conditions

- Selector lever: Other than "P", "R" and "N" positions

- Vehicle speed: 10 km/h (6 MPH) or more

- Engine speed: More than 550 rpm

- Output speed: More than 300 rpm

- Secondary pulley speed: More than 300 rpm

- A lapse of 500 msec or more after the stop lamp switch is turned from ON to OFF.

- Command for the 2GR of auxiliary gearbox is in progress.

- Auxiliary gearbox shifting is not in progress.

- TCM power supply voltage: More than 11 V

- Detection conditions

- Acceleration/deceleration: Less than −0.05 G

- Actual auxiliary gearbox gear ratio − Auxiliary gearbox 2GR ratio ≥ 50%

 - Low brake solenoid valve

- Control valve assembly
The auxiliary gearbox gear ratio is +-10% or less for the auxiliary gearbox 1GR ratio continuously for 500 msec or more under the following diagnosis conditions:

- Diagnosis conditions

- Selector lever: Other than "P", "R" and "N" positions

- Accelerator pedal position: 0.7/8 or more

- Engine speed: More than 550 rpm

- Secondary pulley speed: More than 300 rpm

- Output speed: More than 300 rpm

- Command for the 2GR of auxiliary gearbox is in progress.

- Auxiliary gearbox shifting is not in progress.

- TCM power supply voltage: More than 11 V

DTC COFIRMATION PROCEDURE

CAUTION:

  • Be sure to perform "TM "Diagnosis Procedure"" and then perform "DTC CONFIRMATION PROCEDURE".
  • Never perform "TC CONFIRMATION PROCEDURE" before the repairs. Doing so may result in a secondary malfunction.
  • Be careful of the driving speed.

1.PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.

>> GO TO 2.

2.CHECK DTC DETECTION

  1. Start the engine.
  2. Drive the vehicle.
  3. Maintain the following conditions for 10 seconds or more.
  4. Stop the vehicle
  5. Check the first trip DTC.

Selector lever : "D" position

Accelerator pedal position : 0.7/8 or more

Vehicle speed : 45 km/h (28 MPH) or more

Is "P2859" detected?

YES >> Go to TM "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK INTERMITTENT INCIDENT

Refer to GI "Intermittent Incident".

Is the inspection result normal?

YES >> Replace transaxle assembly. Refer to TM "Removal and Installation".

NO >> Repair or replace malfunctioning parts.

P2858 Clutch B pressure

DTC Logic DTC DETECTION LOGIC DTC Trouble diagnosis name DTC detection condition Possible causes P2858 Clutch B pressure engagement performance The auxiliary gearb ...

P285A Clutch B pressure

DTC Logic DTC DETECTION LOGIC DTC Trouble diagnosis name DTC detection condition Possible causes P285A Clutch B pressure disengagement performance The detection con ...

Other materials:

Engine assembly
Exploded View 1. Engine mounting (RH) stay 2. Engine mount (RH) stay 3. Engine mounting insulator (RH) 4. Rear engine mounting bracket 5. Rear torque rod 6. Engine mounting bracket (LH) 7. Engine mounting bracket (LH) 8. Engine mounting insulator (LH) 9. Mass damper A. Front mark B. Tra ...

Engine control system
ENGINE CONTROL SYSTEM : Component Parts Location 1. Mass air flow sensor (with intake air temperature sensor) 2. Electric throttle control actuator (with built in throttle position sensor and throttle control motor) 3. EVAP canister purge volume control solenoid valve 4. Cooling fan mot ...

Categories


© 2017-2025 Copyright www.niveguide.com
0.0068