Toyota
Nissan Versa
 Sedan Service Manual
Maintenance (MA) » Chassis and body maintenance
Road wheel

ROAD WHEEL : Adjustment

BALANCING WHEELS (ADHESIVE WEIGHT TYPE)

Preparation Before Adjustment

Remove inner and outer balance weights from the road wheel. Using releasing agent, remove double-faced adhesive tape from the road wheel.

CAUTION:

  • Be careful not scratch the road wheel during removal.
  • After removing double-faced adhesive tape, wipe clean traces of releasing agent from the road wheel.

Wheel Balance Adjustment

  • If a balancer machine has an adhesive weight mode setting, select the adhesive weight mode setting and skip Step 2. below. If a balancer machine only has the clip-on (rim flange) weight mode setting, follow Step 2.

    to calculate the correct size adhesive weight.

1. Set road wheel on balancer machine using the center hole as a guide. Start the balancer machine.

2. For balancer machines that only have a clip-on (rim flange) weight mode setting, follow this step to calculate the correct size adhesive weight to use. When inner and outer imbalance values are shown on the balancer machine indicator, multiply outer imbalance value by 5/3 (1.67) to determine balance weight that should be used. Select the outer balance weight with a value closest to the calculated value above and install in to the designated outer position of, or at the designated angle in relation to the road wheel.

a. Indicated imbalance value × 5/3 (1.67) = balance weight to be installed

Calculation example: 23 g (0.81 oz) × 5/3 (1.67) = 38.33 g (1.35 oz) 40 g (1.41 oz) balance weight (closer to calculated balance weight value)

NOTE: Note that balance weight value must be closer to the calculated balance weight value.

Example:

37.4 35 g (1.23 oz)

37.5 40 g (1.41 oz)

Wheel Balance Adjustment

3. Install balance weight in the position shown.

CAUTION:

  • Do not install the inner balance weight before installing the outer balance weight.
  • Before installing the balance weight, be sure to clean the mating surface of the road wheel.
  • When installing balance weight (1) to road wheel, set it into the grooved area (A) on the inner wall of the road wheel as shown so that the balance weight center (B) is aligned with the balancer machine indication position (angle) (C).

CAUTION:

  • Always use Genuine NISSAN adhesive balance weights.
  • Balance weights are non-reusable; always replace with new ones.
  • Do not install more than three sheets of balance weight.

Wheel Balance Adjustment

4. If calculated balance weight value exceeds 50 g (1.76 oz), install two balance weight sheets in line with each other as shown.

CAUTION: Do not install one balance weight sheet on top another.

5. Start balancer machine again.

6. Install balance weight on inner side of road wheel in the balancer machine indication position (angle).

CAUTION: Do not install more than two balance weights.

7. Start balancer machine. Make sure that inner and outer residual imbalance values are 5 g (0.17 oz) each or below.

8. If either residual imbalance value exceeds 5 g (0.17 oz), repeat installation procedures.

Wheel Balance Adjustment

ROAD WHEEL : Tire Rotation

  • Follow the maintenance schedule for tire rotation service intervals.

    Refer to MA "Explanation of General Maintenance".

  • When installing the wheel, tighten wheel nuts to the specified torque.

CAUTION:

  • Do not include the T-type spare tire when rotating the tires.
  • When installing wheels, tighten them diagonally by dividing the work two to three times in order to prevent the wheels from developing any distortion.
  • Be careful not to tighten wheel nut at torque exceeding the criteria for preventing strain of disc rotor.
  • Use NISSAN genuine wheel nuts for aluminum wheels.

ROAD WHEEL : Tire Rotation

Wheel nut tightening torque : 113 N*m (12 kg-m, 83 ft-lb)

  • Perform the ID registration, after tire rotation. Refer to WT "Work Procedure".
    More about «Chassis and body maintenance»:

    Exhaust system

    CVT Fluid

    A/T Fluid

    Clutch fluid

    M/T Oil

    Road wheel

    Brake fluid level and leaks

    Brake lines and cables

    Brake fluid

    Disc brake

    Drum brake

    Steering gear and linkage

    Axle and suspension parts

    Seat belt, buckles, retractors, anchors and adjusters

    Nissan Versa Sedan Service Manual / Maintenance (MA) / Chassis and body maintenance / Road wheel

    Nissan Versa Sedan Service Manual

    Categories


    © 2017-2024 Copyright www.niveguide.com