Nissan Versa (N17): Diagnosis system (IPDM E/R)

Nissan Versa 2nd generation (N17) Service Manual / Body exterior, doors, roof & vehicle security / Security control system (SEC) / Diagnosis system (IPDM E/R)

Diagnosis Description

AUTO ACTIVE TEST

Description

In auto active test, the IPDM E/R sends a drive signal to the following systems to check their operation.

Front wiper (LO, HI)
Parking lamp
License plate lamp
Tail lamp
Front fog lamp
Headlamp (LO, HI)
A/C compressor (magnet clutch)
Cooling fan

Operation Procedure

NOTE: Never perform auto active test in the following conditions.

Passenger door is open
CONSULT is connected

1. Close the hood and lift the wiper arms from the windshield. (Prevent windshield damage due to wiper operation) NOTE: When auto active test is performed with hood opened, sprinkle water on windshield beforehand.

2. Turn the ignition switch OFF.

3. Turn the ignition switch ON, and within 20 seconds, press the driver door switch 10 times. Then turn the ignition switch OFF.

4. Turn the ignition switch ON within 10 seconds. After that the horn sounds once and the auto active test starts.

5. After a series of the following operations is repeated 3 times, auto active test is completed.

NOTE:

When auto active test has to be cancelled halfway through test, turn the ignition switch OFF.
When auto active test is not activated, door switch may be the cause. Check door switch. Refer to DLK "Component Function Check".

Inspection in Auto Active Test

When auto active test is actuated, the following operation sequence is repeated 3 times.

Concept of Auto Active Test

IPDM E/R starts the auto active test with the door switch signals transmitted by BCM via CAN communication.

Therefore, the CAN communication line between IPDM E/R and BCM is considered normal if the auto active test starts successfully.
The auto active test facilitates troubleshooting if any systems controlled by IPDM E/R cannot be operated.

Diagnosis Chart in Auto Active Test

Consult Function (IPDM E/R)

APPLICATION ITEM

CONSULT performs the following functions via CAN communication with IPDM E/R.

ECU IDENTIFICATION

The IPDM E/R part number is displayed.

SELF DIAGNOSTIC RESULT Refer to PCS "DTC Index".

DATA MONITOR

ACTIVE TEST

CAN DIAG SUPPORT MNTR

Refer to LAN "CAN Diagnostic Support Monitor".

ECU DIAGNOSIS INFORMATION

ECM, IPDM E/R, BCM

List of ECU Reference

ECU	Reference
ECM	EC "Reference Value"
	EC "Wiring Diagram"
	EC "Fail Safe"
	EC "DTC Inspection Priority Chart"
	EC "DTC Index"
IPDM E/R	PCS "Reference Value"
	PCS "Wiring Diagram"
	PCS"Fail-Safe"
	PCS"DTC Index"
BCM	BCS "Reference Value"
	BCS "Wiring Diagram"
	BCS "Fail-safe"
	BCS "DTC Inspection Priority Chart"
	BCS "DTC Index"

WIRING DIAGRAM

NVIS

Wiring Diagram

Wiring Diagram

BASIC INSPECTION

Nissan vehicle immobilizer system-NATS

NISSAN VEHICLE IMMOBILIZER SYSTEMNATS : System Diagram NISSAN VEHICLE IMMOBILIZER SYSTEMNATS : System Description INPUT/OUTPUT SIGNAL CHART BCM &n ...

Diagnosis and repair workflow

Work Flow OVERALL SEQUENCE DETAILED FLOW 1.GET INFORMATION FOR SYMPTOM Get the detailed information from the customer about the symptom (the condition and the environment when the incident/ ...

Other materials:

Maintenance precautions
When performing any inspection or maintenance work on your vehicle, always take care to prevent serious accidental injury to yourself or damage to the vehicle. The following are general precautions which should be closely observed. WARNING Park the vehicle on a level surface, apply the pa ...