Toyota
Nissan Versa
 Sedan Service Manual
Engine » Engine control system (EC) » Ignition signal
Diagnosis Procedure

1.CHECK IGNITION COIL POWER SUPPLY CIRCUIT-I

  1. Turn ignition switch OFF, wait at least 10 seconds and then turn ON.
  2. Check the voltage between ECM harness connector and ground. 

Is the inspection result normal?

YES >> GO TO 2.

NO >> Go to EC, "Diagnosis Procedure".

2.CHECK IGNITION COIL POWER SUPPLY CIRCUIT-II

  1. Turn ignition switch OFF.
  2. Disconnect condenser harness connector.
  3. Turn ignition switch ON.
  4. Check the voltage between condenser harness connector and ground. 

Is the inspection result normal?

YES >> GO TO 5.

NO >> GO TO 3.

3.CHECK IGNITION COIL POWER SUPPLY CIRCUIT-III

  1. Turn ignition switch OFF.

  2. Disconnect IPDM E/R harness connector F42.

  3. Check the continuity between IPDM E/R harness connector and condenser harness connector.

  4. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES >> GO TO 11.

NO >> GO TO 4.

4.DETECT MALFUNCTIONING PART

Check the following.

  • Harness for open or short between IPDM E/R and condenser

>> Repair open circuit or short to ground or short to power in harness or connectors.

5.CHECK CONDENSER GROUND CIRCUIT FOR OPEN AND SHORT

  1. Turn ignition switch OFF.

  2. Check the continuity between condenser harness connector and ground. 

  3. Also check harness for short to power.

Is the inspection result normal?

YES >> GO TO 6.

NO >> Repair open circuit or short to ground or short to power in harness or connectors.

6.CHECK CONDENSER

Refer to EC, "Component Inspection (Condenser)"

Is the inspection result normal?

YES >> GO TO 7.

NO >> Replace condenser.

7.CHECK IGNITION COIL POWER SUPPLY CIRCUIT-IV

  1. Reconnect all harness connectors disconnected.

  2. Disconnect ignition coil harness connector.

  3. Turn ignition switch ON.

  4. Check the voltage between ignition coil harness connector and ground.

Is the inspection result normal?

YES >> GO TO 8.

NO >> Repair open circuit or short to ground or short to power in harness or connectors.

8.CHECK IGNITION COIL GROUND CIRCUIT FOR OPEN AND SHORT

  1. Turn ignition switch OFF.
  2. Check the continuity between ignition coil harness connector and ground. 
  3. Also check harness for short to power.

Is the inspection result normal?

YES >> GO TO 9.

NO >> Repair open circuit or short to power in harness or connectors.

9.CHECK IGNITION COIL OUTPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

  1. Disconnect ECM harness connector.
  2. Check the continuity between ECM harness connector and ignition coil harness connector. 
  3. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES >> GO TO 10.

NO >> Repair open circuit or short to ground or short to power in harness or connectors.

10.CHECK IGNITION COIL WITH POWER TRANSISTOR

Refer to EC, "Component Inspection (Ignition Coil with Power Transistor)".

Is the inspection result normal?

YES >> GO TO 11.

NO >> Replace malfunctioning ignition coil with power transistor. Refer to EM, "Removal and Installation".

11.CHECK INTERMITTENT INCIDENT

Refer to GI, "Intermittent Incident".

>> INSPECTION END

    More about «Ignition signal»:

    Component Function Check

    Diagnosis Procedure

    Component Inspection (Ignition Coil with Power Transistor)

    Nissan Versa Sedan Service Manual / Engine / Engine control system (EC) / Ignition signal / Diagnosis Procedure

    Nissan Versa Sedan Service Manual

    Categories


    © 2017-2024 Copyright www.niveguide.com