Nissan Versa (N17): Front combination lamp

Exploded View

Exploded View

1. Front combination lamp (LH)

Removal and Installation

REMOVAL

1. Disconnect the battery negative terminal. Refer to PG "Removal and Installation".

2. Remove front bumper fascia. Refer to EXT "Removal and Installation".

3. Remove the front combination lamp bolts.

4. Pull the headlamp assembly forward slightly.

5. Disconnect the harness connectors from the front combination lamp and remove.

INSTALLATION

Installation is in the reverse order of removal.

NOTE: After installation, perform headlamp aiming adjustment procedure. Refer to EXL "Aiming Adjustment Procedure".

Bulb Replacement

WARNING: Do not touch bulb with your hand while it is on or right after being turned off. Burning may result.

CAUTION:

  • Disconnect the battery negative terminal or remove power circuit fuse while performing the operation.
  • Do not touch the glass surface of the bulb with bare hands or allow oil or grease to get on it to prevent damage to the bulb.
  • Do not leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect the performance of lamp. When replacing bulb, be sure to replace it with new one.

HEADLAMP BULB

Removal

1. Disconnect the harness connector from the headlamp bulb.

2. Remove the cover.

3. Remove the retaining spring lock and the bulb from the front combination lamp.

Installation

Installation is in the reverse order of removal.

CAUTION: After installing the bulb, install the bulb socket securely for watertightness.

PARKING LAMP BULB

Removal

1. Rotate the bulb socket counterclockwise and remove.

2. Remove the bulb from the bulb socket.

Installation

Installation is in the reverse order of removal.

CAUTION: After installing the bulb, install the bulb socket securely for watertightness.

FRONT TURN SIGNAL LAMP BULB

Removal

1. Rotate the bulb socket counterclockwise and remove.

2. Remove the bulb from the bulb socket.

Installation

Installation is in the reverse order of removal.

CAUTION: After installing the bulb, install the bulb socket securely for watertightness.

Disassembly and Assembly

Exploded View

Exploded View

1. Front combination lamp 2. Parking lamp bulb 3. Parking lamp bulb socket 4. Cover 5. Halogen bulb 6. Front turn signal lamp bulb socket 7. Front turn signal lamp bulb 8. Retaining spring

WARNING: Do not touch bulb with your hand while it is on or right after being turned off. Burning may result.

CAUTION:

  • Disconnect the battery negative terminal or remove power circuit fuse while performing the operation.
  • After installing the bulb, install cover and the bulb socket securely for watertightness.
  • Do not touch the glass surface of the bulb with bare hands or allow oil or grease to get on it to prevent damage to the bulb.
  • Do not leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect the performance of lamp. When replacing bulb, be sure to replace it with new one.

DISASSEMBLY

1. Remove the cover.

2. Remove the retaining spring lock and bulb.

3. Rotate the parking lamp bulb socket counterclockwise and remove.

4. Remove the bulb from the parking lamp bulb socket.

5. Rotate the front turn signal lamp bulb socket counterclockwise and remove.

6. Remove the bulb from the front turn signal lamp bulb socket.

ASSEMBLY

Assembly is in the reverse order of disassembly.

Front fog lamp

Exploded View 1. Front fog lamp bulb 2. Front fog lamp 3. Front bumper fascia 4. Front fog lamp finisher ...

Other materials:

Main power supply and ground circuit
Diagnosis Procedure 1.CHECK TCM POWER CIRCUIT (PART 1) Turn ignition switch OFF. Disconnect TCM connector. Check voltage between TCM harness connector terminals and ground.        Is the inspection result normal? YES >> GO TO 2. NO >> G ...

C1145, C1146 Yaw rate/side/decel g sensor
DTC Logic DTC DETECTION LOGIC    DTC CONFIRMATION PROCEDURE 1.CHECK SELF DIAGNOSTIC RESULT With CONSULT. Turn ignition switch OFF to ON. Perform self diagnostic result. Is DTC C1145 or C1146 detected? YES >> Proceed to diagnosis procedure. Refer to BRC "Diagn ...

Categories


© 2017-2025 Copyright www.niveguide.com
0.0087