Description
This malfunction is detected when the A/T does not shift into 4GR position as instructed by TCM. This is not only caused by electrical malfunction (circuits open or shorted) but by mechanical malfunction such as control valve sticking, improper solenoid valve operation, etc.
DTC Logic
DTC DETECTION LOGIC
DTC | Trouble diagnosis name | DTC detection condition | Possible causes |
P074C | Unable to Engage Gear 4 | Under the following diagnosis
conditions, the gear ratio is
1.060 or more continuously for
2 seconds or more. - Diagnosis condition - Shifting is not in progress. - Input speed: 300 rpm or more - Output speed: 300 rpm or more - Engine speed: (Input speed - 50 rpm) or more - Selector lever: D position - Gear: 4GR - Throttle position: 0.7/8.0 or more |
- High clutch/low & reverse
brake solenoid valve - 2-4 brake solenoid valve - Control valve assembly |
DTC CONFIRMATION PROCEDURE
CAUTION:
1.PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT
NOTE: "4TH GR FNCTN P0731" can be used in this diagnosis.
Selector lever : D position
Gear : 4GR
Accelerator pedal position : 0.7/8 or more
Vehicle speed : 20 km/h (13MPH) or more
3. Keep the current driving status for 2 seconds or more if CONSULT screen changes from "OUT OFCONDITION" to "TESTING".
CAUTION: When "TESTING" is not indicated on CONSULT for a long time, check "Self Diagnostic Results" in "TRANSMISSION". When a DTC other than "P074C" is detected, check the DTC. Refer to TM, "DTC Index".
With GST
1. Drive vehicle and maintain the following conditions for 2 seconds or more.
Selector lever : D position
Gear : 4GR
Accelerator pedal position : 0.7/8 or more
Vehicle speed : 20 km/h (13MPH) or more
2. Check the first trip DTC.
Is "OUT OF CONDITION", "STOP VEHICLE" or "COMPLETED RESULT NG" displayed? / Is "P074C" detected?
YES-1 (OUT OF CONDITION.)>>Perform "step 2" again.
YES-2 (STOP VEHICLE.)>>GO TO 3.
YES-3 (COMPLETED RESULT NG)>>Go to TM, "Diagnosis Procedure".
YES-4 ("P074C" is detected.)>>Go to TM, "Diagnosis Procedure".
NO >> GO TO 3.
3.CHECK SYMPTOM
>> INSPECTION END
Diagnosis Procedure
1.MALFUNCTION CAUSE SIMULATION TEST
Refer to GI, "Intermittent Incident".
Is the check result normal?
YES >> Replace the transaxle assembly. Refer to TM, "Removal and Installation".
NO >> Repair or replace the malfunctioning parts.
Description This malfunction is detected when the A/T does not shift into 3GR position as instructed by TCM. This is not only caused by electrical malfunction (circuits open or shorted) but by m ...
Description CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle multiplex communication line with high data communication speed and excellen ...
5Th main gear assembly
Removal and Installation
REMOVAL
Move the shift selector to the 3rd gear position.
Disconnect the shifter cable and the selector cable from shifter lever A
and selector lever. Refer to TM,
"Removal and Installation".
CAUTION:
Do not move shifter lever A and selector leve ...
U0073 Communication bus a off
DTC Logic
DTC
Trouble diagnosis name
DTC detecting condition
Possible causes
U0073
Control Module Communication
Bus "A" Off
When the ignition switch is ON,
TCM detects a bus-off error
continuously for 2 seconds or
more.
Harness or connector
(CA ...