Nissan Versa (N17): VDC OFF Switch

Nissan Versa 2nd generation (N17) Service Manual / Brakes / Brake control system (BRC) / VDC OFF Switch

Component Function Check

1.CHECK VDC OFF SWITCH OPERATION

Check that VDC OFF indicator lamp in combination meter turns ON/OFF when VDC OFF switch is operated.

Is the inspection result normal?

YES >> Inspection End.

NO >> Proceed to diagnosis procedure. Refer to BRC "Diagnosis Procedure".

Diagnosis Procedure

Regarding Wiring Diagram information, refer to BRC "Wiring Diagram".

1.CONNECTOR INSPECTION

  1. Turn ignition switch OFF.
  2. Disconnect ABS actuator and electric unit (control unit) and VDC OFF switch connectors.
  3. Check connectors and terminals for deformation, disconnection, looseness or damage.

Is the inspection result normal?

YES >> GO TO 2

NO >> Repair or replace as necessary.

2.CHECK VDC OFF SWITCH

Check VDC OFF switch. Refer to BRC "Component Inspection".

Is the inspection result normal?

YES >> GO TO 3.

NO >> Replace VDC OFF switch. Refer to BRC "Removal and Installation".

3.CHECK VDC OFF SWITCH SIGNAL

With CONSULT.

  1. Connect ABS actuator and electric unit (control unit) and VDC OFF switch connectors.
  2. Turn ignition switch ON.
  3. In "DATA MONITOR" select "OFF SW" and check VDC OFF switch signal.   

Is the inspection result normal?

YES >> Refer to BRC "Work Flow".

NO >> GO TO 4.

4.CHECK VDC OFF SWITCH CIRCUIT

  1. Turn ignition switch OFF.
  2. Disconnect ABS actuator and electric unit (control unit) and VDC OFF switch connectors.
  3. Check continuity between ABS actuator and electric unit (control unit) connector E33 terminal 15 and VDC OFF switch connector M34 terminal 1. 

    4.   Check continuity between ABS actuator and electric unit (control unit) connector terminal E33 terminal 15 and ground.               

Is the inspection result normal?

YES >> GO TO 5.

NO >> Repair or replace malfunctioning components.

5.CHECK VDC OFF SWITCH GROUND CIRCUIT

Check continuity between VDC OFF switch connector M34 terminal 2 and ground. 

Is the inspection result normal?

YES >> Replace ABS actuator and electric unit (control unit). Refer to BRC "Removal and Installation".

NO >> Repair or replace malfunctioning components.

Component Inspection

1.CHECK VDC OFF SWITCH

  1. Turn ignition switch OFF.
  2. Disconnect VDC OFF switch connector.
  3. Check continuity between terminals of VDC OFF switch connector.

Is the inspection result normal?

YES >> Inspection End.

NO >> Replace VDC OFF switch. Refer to BRC "Removal and Installation".

Parking brake switch

Component Function Check 1.CHECK PARKING BRAKE SWITCH OPERATION Check that brake warning lamp in combination meter turns ON/OFF when parking brake is actuated. Is the inspection result normal? ...

ABS Warning lamp

Component Function Check 1.CHECK ABS WARNING LAMP FUNCTION Check that ABS warning lamp in combination meter turns ON for approximately 2 seconds after ignition switch is turned ON. Is the insp ...

Other materials:

Fuel pressure check
Work Procedure FUEL PRESSURE RELEASE 1.FUEL PRESSURE RELEASE With CONSULT Turn ignition switch ON. Perform "FUEL PRESSURE RELEASE" in "WORK SUPPORT" mode with CONSULT. Start engine. After engine stalls, crank it two or three times to release all fuel pressure. Turn ignition switc ...

Front pillar finisher
FRONT PILLAR FINISHER : Removal and Installation REMOVAL Release front pillar portion of front body side welt. Pull front pillar finisher downward as shown, using mild pressure to disengage the front pillar finisher from the clips. : Clip     3.   Remove the f ...

Categories


© 2017-2025 Copyright www.niveguide.com
0.0056