Toyota
Nissan Versa
 Sedan Service Manual
Transmission & driveline » Transaxle & transmission (TM) » Diagnosis and repair work flow
Work Flow

1.OBTAIN INFORMATION ABOUT SYMPTOM

Refer to TM, "Diagnostic Work Sheet" and interview the customer to obtain the malfunction information (conditions and environment when the malfunction occurred) as much as possible when the customer brings in the vehicle.

>> GO TO 2.

2.CHECK DTC

  1. Before checking the malfunction, check whether any DTC exists.
  2. If DTC exists, perform the following operations.
  • Record the DTC and freeze frame data. (Print out the data using CONSULT and affix them to the Work Order Sheet.)
  • Erase DTCs.
  • Check the relationship between the cause that is clarified with DTC and the malfunction information described by the customer. TM, "Symptom Table" is effective.

    3.   Check the information of related service bulletins and others also.

Do malfunction information and DTC exist?

Malfunction information and DTC exists. >>GO TO 3.

Malfunction information exists, but no DTC. >>GO TO 4.

No malfunction information, but DTC exists. >>GO TO 5.

3.REPRODUCE MALFUNCTION SYMPTOM

Check any malfunction described by a customer, except those with DTC on the vehicle.

Also investigate whether the symptom is a fail-safe or normal operation. Refer to TM, "Fail-Safe".

When a malfunction symptom is reproduced, the question sheet is effective. Refer to TM, "Diagnostic Work Sheet".

Verify the relationship between the symptom and the conditions in which the malfunction described by the customer occurs.

>> GO TO 5.

4.REPRODUCE MALFUNCTION SYMPTOM

Check the malfunction described by the customer on the vehicle.

Also investigate whether the symptom is a fail-safe or normal operation. Refer to TM, "Fail-Safe".

When a malfunction symptom is reproduced, the question sheet is effective. Refer to TM, "Diagnostic Work Sheet".

Verify the relationship between the symptom and the conditions in which the malfunction described by the customer occurs.

>> GO TO 6.

5.PERFORM "DTC CONFIRMATION PROCEDURE"

Perform "DTC CONFIRMATION PROCEDURE" of the appropriate DTC to check if DTC is detected again.

Refer to TM, "DTC Inspection Priority Chart" when multiple DTCs are detected, and then determine the order for performing the diagnosis.

NOTE: If no DTC is detected, refer to the freeze frame data.

Is any DTC detected?

YES >> GO TO 7.

NO >> Check according to GI, "Intermittent Incident".

6.IDENTIFY MALFUNCTIONING SYSTEM WITH "DIAGNOSIS CHART BY SYMPTOM"

Use TM, "Symptom Table" from the symptom inspection result in step 4. Then identify where to start performing the diagnosis based on possible causes and symptoms.

>> GO TO 8.

7.REPAIR OR REPLACE THE MALFUNCTIONING PARTS

Repair or replace the detected malfunctioning parts.

Reconnect parts or connector after repairing or replacing, and then erase DTC if necessary.

>> GO TO 8.

8.FINAL CHECK

Perform "DTC CONFIRMATION PROCEDURE" again to make sure that the repair is correctly performed.

Check that malfunctions are not reproduced when obtaining the malfunction information from the customer, referring to the symptom inspection result in step 3 or 4.

Is DTC or malfunction symptom reproduced?

YES-1 >> DTC is reproduced: GO TO 5.

YES-2 >> Malfunction symptom is reproduced: GO TO 6.

NO >> Before delivering the vehicle to the customer, make sure that DTC is erased.

    More about «Diagnosis and repair work flow»:

    Work Flow

    Diagnostic Work Sheet

    Nissan Versa Sedan Service Manual / Transmission & driveline / Transaxle & transmission (TM) / Diagnosis and repair work flow / Work Flow

    Nissan Versa Sedan Service Manual

    Categories


    © 2017-2020 Copyright www.niveguide.com