DTC DETECTION LOGIC
NOTE: If DTC P0340 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643. Refer to EC, "DTC Logic".
DTC No. | Trouble diagnosis name | DTC detecting condition | Possible cause |
P0340 | Camshaft position sensor (PHASE) circuit |
|
|
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 10.5 V with ignition switch ON.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDUREI
If engine does not start, crank engine for at least 2 seconds.
Is 1st trip DTC detected?
YES >> Go to EC, "Diagnosis Procedure".
NO >> GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDUREII
Is 1st trip DTC detected?
YES >> Go to EC, "Diagnosis Procedure".
NO >> INSPECTION END
1.CHECK STARTING SYSTEM
Turn ignition switch to START position.
Does the engine turn over? Does the starter motor operate?
YES >> GO TO 2.
NO >> Check starting system.
2.CHECK GROUND CONNECTION
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace ground connection.
3.CHECK INTAKE CAMSHAFT POSITION SENSOR (PHASE) POWER SUPPLY CIRCUIT
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair open circuit or short to ground or short to power in harness or connectors.
4.CHECK INTAKE CAMSHAFT POSITION SENSOR GROUND CIRCUIT FOR OPEN AND SHORT
4. Also check harness for short to ground and short to power.
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair open circuit or short to ground or short to power in harness or connectors.
5.CHECK INTAKE CAMSHAFT POSITION SENSOR (PHASE) INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1. Check the continuity between intake
camshaft position sensor (PHASE) harness connector and ECM harness
connector.
2. Also check harness for short to ground and short to power.
Is the inspection result normal?
YES >> GO TO 6.
NO >> Repair open circuit or short to ground or short to power in harness or connectors.
6.CHECK INTAKE CAMSHAFT POSITION SENSOR (PHASE)
Refer to EC, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 7.
NO >> Replace intake camshaft position sensor (PHASE). Refer to EM, "Exploded View".
7.CHECK CAMSHAFT (INT)
Check the following.
Is the inspection result normal?
YES >> GO TO 8.
NO >> Remove debris and clean the signal plate of camshaft rear end or replace camshaft. Refer to EM, "Removal and Installation".
8.CHECK INTERMITTENT INCIDENT
Refer to GI, "Intermittent Incident".
>> INSPECTION END
1.CHECK INTAKE CAMSHAFT POSITION SENSORI
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace intake camshaft position sensor. Refer to EM, "Exploded View".
2.CHECK INTAKE CAMSHAFT POSITION SENSORII
Check resistance intake camshaft position sensor terminals as follows.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace intake camshaft position sensor. Refer to EM, "Exploded View".
Insufficient cooling
Description
Symptom
Insufficient cooling
No cool air comes out. (Air flow volume is normal.)
Diagnosis Procedure
NOTE:
Perform self-diagnosis with CONSULT before performing symptom diagnosis. If any
malfunction result or DTC
is detected, perform the corresponding diagnosis.
1.CHE ...
Door outside molding
Exploded View
1. Front door panel 2. Rear door panel 3. Front door outside molding
4. Rear door outside molding Pawl
Removal and Installation
FRONT DOOR OUTSIDE MOLDING
Removal
1. Open front door glass.
2. Release pawl, twist front door outside molding toward the outside of the
vehicl ...