Description
Detects door open/close condition and transmits the signal to BCM.
1. CHECK FRONT DOOR SWITCH INPUT SIGNAL
Check ("DOOR SW-DR" and "DOOR SW-AS") in "DATA MONITOR" mode with CONSULT.
Refer to BCS
"RETAINED PWR : CONSULT Function (BCM - RETAINED PWR)" or BCS "RETAINED PWR :
CONSULT
Function (BCM - RETAINED PWR)".
Is the inspection result normal?
YES >> Front door switch circuit is OK.
NO >> Refer to PWC "Diagnosis Procedure".
Regarding Wiring Diagram information, refer to PWC "Wiring Diagram".
1. CHECK HARNESS CONTINUITY
Check voltage between BCM connector and ground.
Is the measurement value within the specification?
YES >> Replace BCM. Refer to BCS "Removal and Installation" or BCS "Removal and Installation".
NO >> GO TO 2
2. CHECK HARNESS CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect BCM and front door switch.
3. Check continuity between BCM connector and front door switch connector.
4. Check continuity between BCM connector and ground.
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK BCM OUTPUT SIGNAL
1. Connect BCM connector.
2. Check voltage between BCM connector and ground.
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK BCM OUTPUT SIGNAL
1. Connect BCM connector.
2. Check voltage between BCM connector and ground.
Component Inspection
1. CHECK FRONT DOOR SWITCH
Check front door switches
.
Is the inspection result normal?
YES >> Front door switch is OK.
NO >> Replace front door switch.
SYMPTOM DIAGNOSIS
POWER WINDOW CONTROL SYSTEM SYMPTOMS
Symptom Table
Symptom | Reference page |
None of the power windows can be operated using any switch. | Refer to PWC"Diagnosis Procedure". |
Driver side power window does not operate. | Refer to PWC"Diagnosis Procedure". |
Front passenger side power window does not operate (When both power window main switch and front power window switch are operated). | Refer to PWC"WHEN BOTH POWER WINDOW MAIN SWITCH AND FRONT POWER WINDOW SWITCH ARE OPERATED : Diagnosis Procedure". |
Front passenger side power window does not operate (when front power window switch RH is operated). | Refer to PWC"WHEN FRONT POWER WINDOW SWITCH (PASSENGER SIDE) IS OPERATED : Diagnosis Procedure". |
Front passenger side power window does not operate (when power window switch main is operated). | Refer to PWC "WHEN POWER WINDOW MAIN SWITCH IS OPERATED : Diagnosis Procedure". |
Rear (LH) side power window does not operate (when both power window main switch and rear power window switch LH are operated). | Refer to PWC "WHEN BOTH POWER WINDOW MAIN SWITCH AND REAR POWER WINDOW SWITCH LH ARE OPERATED : Diagnosis Procedure". |
Rear (LH) side power window does not operate (when rear power window switch LH is operated). | Refer to PWC "WHEN REAR POWER WINDOW SWITCH LH IS OPERATED : Diagnosis Procedure". |
Rear (LH) side power window does not operate (when power window main switch is operated). | Refer to PWC "WHEN POWER WINDOW MAIN SWITCH IS OPERATED : Diagnosis Procedure". |
Rear (RH) side power window does not operate (when both power window main switch and rear power window switch RH are operated). | Refer to PWC "WHEN BOTH POWER WINDOW MAIN SWITCH AND REAR POWER WINDOW SWITCH RH ARE OPERATED : Diagnosis Procedure". |
Rear (RH) side power window does not operate (when rear power window switch RH is operated). | Refer to PWC "WHEN REAR POWER WINDOW SWITCH RH IS OPERATED : Diagnosis Procedure". |
Rear (RH) side power window does not operate (when power window main switch is operated) | Refer to PWC "WHEN POWER WINDOW MAIN SWITCH IS OPERATED : Diagnosis Procedure". |
Power window lock switch does not function. | Refer to PWC "Diagnosis Procedure". |
Diagnosis Procedure 1.CHECK BCM POWER SUPPLY AND GROUND CIRCUIT Check BCM power supply and ground circuit. Refer to PWC "BCM (BODY CONTROL SYSTEM) (WITH INTELLIGENT KEY SYSTEM) : Diagnosis P ...
P0607 ECM
DTC Logic
DTC DETECTION LOGIC
DTC No.
Trouble diagnosis
(Trouble diagnosis content)
DTC detecting condition
Possible cause
P0607
ECM
(CAN communication bus)
When detecting error during the initial diagnosis
of CAN controller of ECM.
ECM
DTC CO ...
P062F EEPROM
Description
TCM checks the value read in FLASH ROM at ignition switch ON, and judges if
there is writing failure to
FLASH ROM or malfunction of FLASH ROM.
DTC Logic
DTC DETECTION LOGIC
DTC
Trouble diagnosis name
DTC detection condition
Possible causes
P062F
Inter ...