Nissan Versa (N17): Overdrive control switch

Nissan Versa 2nd generation (N17) Service Manual / Transmission & driveline / Transaxle & transmission (TM) / Overdrive control switch

Component Function Check

1.CHECK O/D INDICATOR LAMP FUNCTION

Check O/D OFF indicator lamp turns ON for approx. 2 seconds when ignition switch turns ON.

Is the inspection results normal?

YES >> GO TO 2.

NO >> Go to TM, "Diagnosis Procedure".

2.CHECK O/D SWITCH FUNCTION

  1. Shift the selector lever to "D" position.
  2. Check that O/D OFF indicator lamp turns ON/OFF when sport mode switch is operated.

Is the inspection results normal?

YES >> INSPECTION END

NO >> Go to TM, "Diagnosis Procedure".

Diagnosis Procedure

1.CHECK OVERDRIVE CONTROL SWITCH CIRCUIT

  1. Turn ignition switch OFF.
  2. Disconnect A/T shift selector connector.
  3. Turn ignition switch ON.
  4. Check the voltage between A/T shift selector harness connector terminals. 

Is the inspection result normal?

YES >> GO TO 2.

NO >> GO TO 3.

2.CHECK OVERDRIVE CONTROL SWITCH

Check overdrive control switch. Refer to TM, "Component Inspection (Overdrive Control Switch)".

Is the inspection result normal?

YES >> Check intermittent incident. Refer to GI "Intermittent Incident".

NO >> Repair or replace the malfunctioning parts.

3.CHECK GROUND CIRCUIT

Check the continuity between A/T shift selector harness connector terminal and ground.

Is the inspection result normal?

YES >> GO TO 4.

NO >> Repair or replace the malfunctioning parts.

4.CHECK CIRCUIT BETWEEN COMBINATION METER AND A/T SHIFT SELECTOR (PART 1)

  1. Turn ignition switch OFF.
  2. Disconnect combination meter connector.
  3. Check the continuity between combination meter harness connector terminal and A/T shift selector harness connector terminal. 

Is the inspection result normal?

YES >> GO TO 5.

NO >> Repair or replace the malfunctioning parts.

5.CHECK CIRCUIT BETWEEN COMBINATION METER AND A/T SHIFT SELECTOR (PART 2)

Check the continuity between combination meter harness connector terminal and ground. 

Is the inspection result normal?

YES >> GO TO 6.

NO >> Repair or replace the malfunctioning parts.

6.CHECK COMBINATION METER INPUT SIGNAL

  1. Connect all of the disconnected connectors.
  2. Turn ignition switch ON.
  3. Select "Data Monitor" in "METER/M&A".
  4. Select "O/D OFF SW".
  5. Check that "O/D OFF SW" turns ON/OFF when overdrive control switch is operated. Refer to MWI, "Reference Value".

Is the inspection result normal?

YES >> Check intermittent incident. Refer to GI "Intermittent Incident".

NO >> Replace combination meter. Refer to MWI "Removal and Installation".

Component Inspection (Overdrive Control Switch)

1.CHECK OVERDRIVE CONTROL SWITCH

Check the continuity between wires of selector lever knob (1)

CHECK OVERDRIVE CONTROL SWITCH

Is the inspection result normal?

YES >> INSPECTION END

NO >> Replace the selector lever knob. Refer to TM "Removal and Installation".

Main power supply and ground circuit

Diagnosis Procedure 1.CHECK TCM POWER CIRCUIT 1 Turn the ignition switch OFF. Disconnect the TCM connector. Check the voltage between the TCM harness connector terminals and ground.  ...

O/D OFF indicator lamp

Component Function Check 1.CHECK O/D OFF INDICATOR LAMP FUNCTION Check O/D OFF indicator lamp turns ON for approx. 2 seconds when ignition switch turns ON. Is the inspection results normal? YE ...

Other materials:

Vehicle Dynamic Control (VDC) off switch
The vehicle should be driven with the VDC system on for most driving conditions. If the vehicle is stuck in mud or snow, the VDC system reduces the engine output to reduce wheel spin. The engine speed will be reduced even if the accelerator is depressed to the floor. If maximum engine po ...

If your vehicle overheats
If your vehicle is overheating (indicated by an extremely high temperature gauge reading (if so equipped), a red high temperature warning light (if so equipped) ), or if you feel a lack of engine power, detect abnormal noise, etc. take the following steps. WARNING Do not continue to driv ...

Categories


© 2017-2025 Copyright www.niveguide.com
0.0069