Nissan Versa (N17): P0182, P0183 FTT sensor

DTC Logic

DTC DETECTION LOGIC

DTC No. Trouble diagnosis name DTC detecting condition Possible cause
P0182 FTT SEN/CIRCUIT (Fuel tank temperature sensor circuit low input) An excessively low voltage from the sensor is sent to ECM.
  • Harness or connectors (The FTT sensor circuit is open or shorted.)
  • Fuel tank temperature sensor
  • Combination meter
P0183 FTT SEN/CIRCUIT (Fuel tank temperature sensor circuit high input) An excessively high voltage from the sensor is sent to ECM.

DTC CONFIRMATION PROCEDURE

1.PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.
  2. Turn ignition switch ON.
  3. Turn ignition switch OFF and wait at least 10 seconds.

>> GO TO 2.

2.PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON and wait at least 5 seconds.
  2. Check 1st trip DTC.

Is 1st trip DTC detected?

YES >> Proceed to EC, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK DTC WITH COMBINATION METER

Check DTC with combination meter. Refer to MWI, "CONSULT Function" (TYPE A) or MWI, "CONSULT Function" (TYPE B). Check the vehicle type to confirm the service information in MWI section. Refer to MWI, "Information".

Is the inspection result normal?

YES >> GO TO 2.

NO >> Proceed to MWI, "Component Function Check" (TYPE A) or MWI, "Component Function Check" (TYPE B).

2.CHECK FUEL TANK TEMPERATURE (FTT) SENSOR POWER SUPPLY

  1. Turn ignition switch OFF.
  2. Disconnect fuel level sensor unit and fuel pump harness connector.
  3. Turn ignition switch ON.
  4. Check the voltage between fuel level sensor unit and fuel pump harness connector and ground.

Is the inspection result normal?

YES >> GO TO 4.

NO >> GO TO 3.

3.CHECK FUEL TANK TEMPERATURE (FTT) SENSOR POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.
  2. Disconnect ECM harness connector.
  3. Check the continuity between fuel level sensor unit and fuel pump harness connector and ECM harness connector.

    4.   Also check harness for short to ground and to power.

Is the inspection result normal?

YES >> Perform the trouble diagnosis for power supply circuit.

NO >> Repair or replace errordetected parts.

4.CHECK FUEL TANK TEMPERATURE (FTT) SENSOR GROUND CIRCUIT

  1. Turn ignition switch OFF.
  2. Disconnect ECM harness connector.
  3. Check the continuity between fuel level sensor unit and fuel pump harness connector and ECM harness connector.

    4.   Also check harness for short to power.

Is the inspection result normal?

YES >> GO TO 5.

NO >> Repair or replace errordetected parts.

5.CHECK FUEL TANK TEMPERATURE (FTT) SENSOR

Check the FTT sensor. Refer to EC, "Component Inspection".

Is the inspection result normal?

YES >> Check intermittent incident. Refer to GI, "Intermittent Incident".

NO >> Replace "fuel level sensor unit and fuel pump". Refer to FL, "Removal and Installation".

Component Inspection

1.CHECK FUEL TANK TEMPERATURE (FTT) SENSOR

  1. Turn ignition switch OFF.
  2. Disconnect fuel level sensor unit and fuel pump harness connector.
  3. Remove fuel level sensor unit. Refer to FL5, "Removal and Installation".
  4. Check resistance between fuel level sensor unit and fuel pump terminals by heating with hot water as shown in the figure.

CHECK FUEL TANK TEMPERATURE (FTT) SENSOR

Is the inspection result normal?

YES >> INSPECTION END

NO >> Replace fuel level sensor unit and fuel pump. Refer to FL, "Removal and Installation".

Other materials:

Additional service when replacing ECM
Description When replacing ECM, the following procedure must be performed. PROGRAMMING OPERATION NOTE: After replacing with a blank ECM, programming is required to write ECM information. Be sure to follow the procedure to perform the programming. Work Procedure 1.CHECK ECM PART NUMBER Che ...

P0607 ECM
DTC Logic DTC DETECTION LOGIC DTC No. Trouble diagnosis (Trouble diagnosis content) DTC detecting condition Possible cause P0607 ECM (CAN communication bus) When detecting error during the initial diagnosis of CAN controller of ECM. ECM DTC CO ...

Categories


© 2017-2025 Copyright www.niveguide.com
0.0097