Nissan Versa (N17): P0744 Torque converter

Nissan Versa 2nd generation (N17) Service Manual / Transmission & driveline / Transaxle & transmission (TM) / P0744 Torque converter

DTC Logic

DTC DETECTION LOGIC

DTC Trouble diagnosis name DTC detection condition Possible causes
P0744 Torque converter clutch circuit intermittent The torque converter slip speed is at or above a set value (40 rpm + (Vehicle speed / 2) continuously for 30 seconds or more under the following diagnosis conditions:

- Diagnosis conditions

- Selector lever: "D" position

- Accelerator pedal position: 1.0/8 or more

- Vehicle speed: 10 km/h (6 MPH) or more

- Engine speed: 450 rpm or more

- CVT fluid temperature: 20C (68F) ≤ CVT fluid temperature ≤ 180C (356F)

- Lockup command is being given (except for slip lockup).

- LU PRS: More than 0.2 MPa

- TCM power supply voltage: More than 11 V

- Torque converter clutch solenoid valve

- Control valve assembly

- Torque converter

DTC CONFIRMATION PROCEDURE

CAUTION: Be careful of the driving speed.

1.PREPARATION BEFORE OPERATION 1

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.

>> GO TO 2.

2.PREPARATION BEFORE OPERATION 2

With CONSULT

  1. Start the engine.
  2. Select "Data Monitor" in "TRANSMISSION".
  3. Select "FLUID TEMP".
  4. Confirm that the CVT fluid temperature is in the range below.

FLUID TEMP : 20C (68F) or more

With GST

  1. Start the engine.
  2. Set the CVT fluid to 20C (68F) or more.

    NOTE: When the ambient temperature is 20C (68F), the CVT fluid usually increases to 50 to 80C (122 to 176F) with driving in an urban area for approximately 10 minutes.

Is the CVT fluid 20C (68F) or more?

YES >> GO TO 3.

NO >> 1. Warm the transaxle.  2. GO TO 3.

3.CHECK DTC DETECTION

  1. Drive the vehicle.
  2. Maintain the following conditions for 40 seconds or more.

Selector lever : "D" position

Accelerator pedal position : 1.0/8 or more

Vehicle speed : 40 km/h (25 MPH) or more

    3.   Stop the vehicle.

    4.   Check the first trip DTC.

Is "P0744" detected?

YES >> Go to TM "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK LINE PRESSURE

Perform line pressure test. Refer to TM "Work Procedure".

Is the inspection result normal?

YES >> GO TO 2.

NO >> Repair or replace the malfunction items.

2.CHECK TORQUE CONVERTER CLUTCH SOLENOID VALVE

  1. Turn ignition switch OFF.
  2. Disconnect CVT unit connector.
  3. Check torque converter clutch solenoid valve. Refer to TM "Component Inspection (Torque Converter Clutch Solenoid Valve)".

Is the inspection result normal?

YES >> GO TO 3.

NO >> Repair or replace the malfunction items.

3.CHECK INTERMITTENT INCIDENT

Refer to GI "Intermittent Incident".

Is the inspection result normal?

YES >> Replace the transaxle assembly. Refer to TM, "Removal and Installation".

NO >> Repair or replace the malfunction items.

Component Inspection (Torque Converter Clutch Solenoid Valve)

1.CHECK TORQUE CONVERTER CLUTCH SOLENOID VALVE

Check resistance between CVT unit connector terminal and ground.  

Is the inspection result normal?

YES >> INSPECTION END

NO >> There is a malfunction of torque converter clutch solenoid valve. Replace transaxle assembly.

Refer to TM "Removal and Installation".

Other materials:

Doors
When the doors are locked using one of the following methods, the doors cannot be opened using the inside or outside door handles. The doors must be unlocked to open the doors. WARNING Before opening any door, always look for and avoid oncoming traffic. To help avoid risk of injury or de ...

Windshield-washer fluid
Windshield-washer fluid reservoir Add a washer solvent to the windshield-washer fluid reservoir for better cleaning. In the winter season, add a windshield-washer antifreeze. Follow the manufacturer's instructions for the mixture ratio. Refill the reservoir more frequently when driving ...

Categories


© 2017-2025 Copyright www.niveguide.com
0.0083