Nissan Versa (N17): Wheel sensor

Front wheel sensor

FRONT WHEEL SENSOR : Exploded View

FRONT WHEEL SENSOR : Exploded View

1. Front wheel sensor (LH) 2. Front wheel sensor harness connector (LH) Front

FRONT WHEEL SENSOR : Removal and Installation

CAUTION:

  • Be careful not to damage wheel sensor edge and sensor rotor teeth.
  • When removing the front wheel hub, first remove the wheel sensor from the wheel hub. Failure to do so may result in damage to the wheel sensor wires, making the sensor inoperative.
  • Pull out the wheel sensor, being careful to turn it as little as possible. Do not pull on the wheel sensor harness.
  • Before installation, check if foreign objects, such as iron fragments, are adhered to the pick-up part of the sensor or to the inside of the hole in the wheel hub for the wheel sensor, or if a foreign object is caught in the surface of the mating surface for the sensor rotor. Fix as necessary and then install the wheel sensor.

REMOVAL

  1. Remove wheel and tire using power tool. Refer to WT "Adjustment".
  2. Remove the fender protector (front). Refer to EXT "Removal and Installation".
  3. Remove front wheel sensor from steering knuckle.
  4. Remove front wheel sensor harness from the vehicle.

INSTALLATION

Installation is in the reverse order of the removal.

CAUTION: Do not twist front wheel sensor harness when installing front wheel sensor. Check that grommet (2) is fully inserted to bracket (1). Check that front wheel sensor harness is not twisted after installation.

INSTALLATION

Rear wheel sensor

REAR WHEEL SENSOR : Exploded View

REAR WHEEL SENSOR : Exploded View

1. Rear wheel sensor (LH) 2. Rear wheel sensor harness connector (LH) Front

REAR WHEEL SENSOR : Removal and Installation

CAUTION:

  • Be careful not to damage wheel sensor edge and sensor rotor teeth.
  • When removing the front or rear wheel hub, first remove the wheel sensor from the wheel hub. Failure to do so may result in damage to the wheel sensor wires, making the sensor inoperative.
  • Pull out the wheel sensor, being careful to turn it as little as possible. Do not pull on the wheel sensor harness.
  • Before installation, check if foreign objects, such as iron fragments, are adhered to the pick-up part of the sensor or to the inside of the hole in the wheel hub for the wheel sensor, or if a foreign object is caught in the surface of the mating surface for the sensor rotor. Fix as necessary and then install the wheel sensor.

REMOVAL

  1. Remove rear wheel sensor from back plate.
  2. Remove rear wheel sensor harness from the vehicle.

INSTALLATION

Installation is in the reverse order of removal.

CAUTION: Do not twist rear wheel sensor harness when installing rear wheel sensor. Check that grommet (2) is fully inserted to bracket (1). Check that rear wheel sensor harness is not twisted after installation.

INSTALLATION

Vehicle jerks during VDC/TCS/ABS control

Diagnosis Procedure 1.SYMPTOM CHECK Check if the vehicle jerks during VDC/TCS/ABS control. Is the inspection result normal? YES >> Inspection End. NO >> GO TO 2 2.CHECK SELF DIAGNO ...

Sensor rotor

FRONT SENSOR ROTOR FRONT SENSOR ROTOR : Removal and Installation REMOVAL The front wheel sensor rotor is an integral part of the wheel hub and bearing assembly and can not be replaced individual ...

Other materials:

Cleaning interior
Occasionally remove loose dust from the interior trim, plastic parts and seats using a vacuum cleaner or soft bristled brush. Wipe the vinyl and leather surfaces with a clean, soft cloth dampened in mild soap solution, then wipe clean with a dry, soft cloth. Regular care and cleaning is requ ...

Side oil seal
Removal and Installation REMOVAL Remove front drive shaft from transaxle assembly. Refer to FAX, "Removal and Installation". Remove differential side oil seal (1) using suitable tool. CAUTION: Do not damage transaxle case and clutch housing. INSTALLATION   & ...

Categories


© 2017-2025 Copyright www.niveguide.com
0.0073