Nissan Versa (N17): Push-button ignition switch illumination circuit

Nissan Versa 2nd generation (N17) Service Manual / Driver controls / Interior lighting system (INL) / Push-button ignition switch illumination circuit

Description

Provides the power supply and the ground to control the push-button ignition switch illumination.

Component Function Check

1.CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION OPERATION

CONSULT

1. Turn the ignition switch ON.

2. Select ENGINE SW ILLUMI of BCM (INTELLGENT KEY) active test item.

3. While operating the test item, check that the push-button ignition switch illumination turns ON/OFF

ON : Push-button ignition switch illumination ON

OFF : Push-button ignition switch illumination OFF

Is the inspection result normal?

YES >> Push-button ignition switch illumination circuit is normal.

NO >> Refer to INL "Diagnosis Procedure".

Diagnosis Procedure

Regarding Wiring Diagram information, refer to INL "Wiring Diagram".

1.CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION OPERATION

CONSULT

1. Turn the ignition switch ON.

2. Select ENGINE SW ILLUMI of BCM (INTELLIGENT KEY) active test item.

3. While operating the test item, check voltage between push-button ignition switch connector M25 terminal 5 and ground.

Is the inspection result normal?

YES >> GO TO 4

NO >> GO TO 2

2.CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION POWER SUPPLY OPEN CIRCUIT

1. Turn the ignition switch OFF.

2. Disconnect BCM connector M98 and push-button ignition switch connector.

3. Check continuity between BCM connector M98 terminal 90 and push-button ignition switch connector M25 terminal 5.

Is the inspection result normal?

YES >> GO TO 3.

NO >> Repair or replace the harness or connectors.

3.CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION POWER SUPPLY SHORT CIRCUIT

Check continuity between BCM connector M98 terminal 90 and ground.

Is the inspection result normal?

YES >> Replace BCM. Refer to BCS "Removal and Installation".

NO >> Repair or replace the harness or connectors.

4.CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION GROUND CIRCUIT

1. Turn the ignition switch OFF

2. Disconnect push-button ignition switch connector.

3. Check continuity between push-button ignition switch connector M25 terminal 6 and ground.

Is the inspection result normal?

YES >> Replace push-button ignition switch. Refer to PCS "Removal and Installation".

NO >> GO TO 5.

5.CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION GROUND OPEN CIRCUIT

1. Disconnect BCM connector M98.

2. Check continuity between BCM connector M98 terminal 92 and push-button ignition switch connector M25 terminal 6.

Is the inspection result normal?

YES >> Replace BCM. Refer to BCS "Removal and Installation".

NO >> Repair or replace the harness or connectors.

SYMPTOM DIAGNOSIS

INTERIOR LIGHTING SYSTEM SYMPTOMS

Symptom Table

CAUTION: Perform the self-diagnosis with CONSULT before the symptom diagnosis. Perform the trouble diagnosis if any DTC is detected.

Symptom Table

REMOVAL AND INSTALLATION

Trunk room lamp circuit

Description Controls the trunk room lamp (ground side) to turn the trunk room lamp ON and OFF. Component Function Check CAUTION: Before performing the diagnosis, check that the following is ...

Map lamp

Exploded View 1. Map lamp bulb housing 2. Bulb 3. Lens Pawl ...

Other materials:

Sun visors
1. To block glare from the front, swing down the sun visor 1 . 2. To block glare from the side, remove the sun visor from the center mount and swing the visor to the side 2 . 3. Slide the extension 3 sun visor in or out as needed. CAUTION Do not store the sun visor before returning ...

TCM
Exploded View 1. TCM 2. Bracket 3. Clips Front Removal and Installation NOTE: When replacing the TCM and transaxle assembly as a set, replace the transaxle assembly first and then replace the TCM. Refer to TM, "Description". REMOVAL Remove the battery. Refer to PG &q ...

Categories


© 2017-2025 Copyright www.niveguide.com
0.0071