DTC DETECTION LOGIC
DTC No. | Trouble diagnosis name (Trouble diagnosis content) | DTC detecting condition | Possible cause | |
P0181 | FTT SENSOR [Fuel tank temperature (FTT) sensor circuit range/performance] | A | Rationally incorrect voltage from the sensor is sent to ECM, compared with the voltage signals from ECT sensor and intake air temperature sensor. |
|
B | The comparison result of signals transmitted to ECM from each temperature sensor (IAT sensor, ECT sensor, EOT sensor, and FTT sensor) shows that the voltage signal of the FTT sensor is higher/lower than that of other temperature sensors when the engine is started with its cold state. |
|
DTC CONFIRMATION PROCEDURE
1.INSPECTION START
Is it necessary to erase permanent DTC?
YES >> GO TO 7.
NO >> GO TO 2.
2.PRECONDITIONING
If DTC CONFIRMATION PROCEDURE has been previously conducted, always perform the following procedure before conducting the next test.
>> GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION AI
Is 1st trip DTC detected?
YES >> Proceed to EC, "Diagnosis Procedure".
NO >> GO TO 4.
4.CHECK ENGINE COOLANT TEMPERATURE
With CONSULT
With GST
Follow the procedure "With CONSULT" above.
"COOLAN TEMP/S" less than 60C (140F)?
YES >> INSPECTION END
NO >> GO TO 5.
5.PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION AII
With CONSULT
With GST
Follow the procedure "With CONSULT" above.
Is 1st trip DTC detected?
YES >> Proceed to EC, "Diagnosis Procedure".
NO >> GO TO 6.
6.PERFORM COMPONENT FUNCTION CHECK (FOR MALFUNCTION B)
Perform component function check. Refer to EC, "Component Function Check".
NOTE: Use the component function check to check the overall function of the FTT sensor circuit. During this check, a 1st trip DTC might not be confirmed.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Proceed to EC, "Diagnosis Procedure".
7.PRECONDITIONING
If DTC CONFIRMATION PROCEDURE has been previously conducted, always perform the following procedure before conducting the next test.
TESTING CONDITION:
>> GO TO 8.
8.PERFORM DTC CONFIRMATION PROCEDURE B
NOTE: Cool the vehicle in an environment of ambient air temperature between −10C (14F) and 35C (95F).
3. Turn ignition switch OFF and soak the vehicle for 12 hours.
CAUTION: Never turn ignition switch ON during soaking.
NOTE: The vehicle must be cooled with the food open.
4. Start engine and let it idle for 5 minutes or more.
CAUTION: Never turn ignition switch OFF during idling.
5. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC, "Diagnosis Procedure".
NO >> INSPECTION END
1.CHECK FUEL TANK TEMPERATURE (FTT) SENSOR
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI, "Intermittent Incident".
NO >> Proceed to EC, "Diagnosis Procedure".
1.INSPECTION START
Confirm the detected malfunction (A or B). Refer to EC, "DTC Logic".
Which malfunction is detected?
A >> GO TO 2.
B >> GO TO 6.
2.CHECK DTC WITH COMBINATION METER
Check DTC with combination meter. Refer to MWI, "CONSULT Function" (TYPE A) or MWI, "CONSULT Function" (TYPE B). Check the vehicle type to confirm the service information in MWI section. Refer to MWI, "Information".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Proceed to MWI, "Component Function Check" (TYPE A) or MWI, "Component Function Check" (TYPE B).
3.CHECK FUEL TANK TEMPERATURE (FTT) SENSOR POWER
Is the inspection result normal?
YES >> GO TO 5.
NO >> GO TO 4.
4.CHECK FUEL TANK TEMPERATURE (FTT) SENSOR POWER SUPPLY CIRCUIT
4. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO >> Repair or replace errordetected parts.
5.CHECK FTT SENSOR GROUND CIRCUIT
4. Also check harness for short to power.
Is the inspection result normal?
YES >> GO TO 6.
NO >> Repair or replace errordetected parts.
6.CHECK FUEL TANK TEMPERATURE (FTT) SENSOR
Check the FTT sensor. Refer to EC, "Component Inspection".
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI, "Intermittent Incident".
NO >> Replace fuel level sensor unit and fuel pump. Refer to FL, "Removal and Installation".
1.CHECK FUEL TANK TEMPERATURE (FTT) SENSOR
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace fuel level sensor unit and fuel pump. Refer to FL, "Removal and Installation".
Automatic speed control device (ASCD)
Automatic speed control device (ascd) : system diagram
NOTE:
Transmission range switch and TCM is also for A/T models.
Automatic speed control device (ascd) : system description
INPUT/OUTPUT SIGNAL CHART
Sensor
Input signal to ECM
ECM function
Actuator
Brake pedal ...
Control cable
Exploded View
1. Bracket B 2. Lock plate 3. Transaxle assembly
4. Bracket A 5. Control cable 6. Shift selector assembly
A: Manual lever B: Grommet
Removal and Installation
CAUTION:
Always apply the parking brake before performing removal and installation.
REMOVAL
Remove the battery. R ...