Nissan Versa (N17): Refrigerant pressure sensor

Nissan Versa 2nd generation (N17) Service Manual / Engine / Engine control system (EC) / Refrigerant pressure sensor

Component Function Check

1.CHECK REFRIGERANT PRESSURE SENSOR OVERALL FUNCTION

  1. Start engine and warm it up to normal operating temperature.
  2. Turn A/C switch and blower fan switch ON.
  3. Check the voltage between ECM harness connector and ground.  

Is the inspection result normal?

YES >> INSPECTION END

NO >> Go to EC, "Diagnosis Procedure".

Diagnosis Procedure

1.CHECK GROUND CONNECTION

  1. Turn A/C switch and blower fan switch OFF.
  2. Stop engine.
  3. Turn ignition switch OFF.
  4. Check ground connection E15. Refer to Ground Inspection in GI, "Circuit Inspection".

Is the inspection result normal?

YES >> GO TO 2.

NO >> Repair or replace ground connection.

2.CHECK REFRIGERANT PRESSURE SENSOR POWER SUPPLY CIRCUIT

  1. Disconnect refrigerant pressure sensor harness connector.
  2. Turn ignition switch ON.
  3. Check the voltage between refrigerant pressure sensor harness connector and ground

Is the inspection result normal?

YES >> GO TO 4.

NO >> GO TO 3.

3.DETECT MALFUNCTIONING PART

Check the following.

  • Harness for open or short between ECM and refrigerant pressure sensor

>> Repair open circuit or short to ground or short to power in harness or connectors.

4.CHECK REFRIGERANT PRESSURE SENSOR GROUND CIRCUIT FOR OPEN AND SHORT

  1. Turn ignition switch OFF.
  2. Disconnect ECM harness connector.
  3. Check the continuity between refrigerant pressure sensor harness connector and ECM harness connector.
  4. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES >> GO TO 6.

NO >> GO TO 5.

5.DETECT MALFUNCTIONING PART

Check the following.

  • Harness for open or short between ECM and refrigerant pressure sensor

>> Repair open circuit or short to ground or short to power in harness or connectors.

6.CHECK REFRIGERANT PRESSURE SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

  1. Check the continuity between ECM harness connector and refrigerant pressure sensor harness connector.
  2. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES >> GO TO 8.

NO >> GO TO 7.

7.DETECT MALFUNCTIONING PART

Check the following.

  • Harness for open or short between ECM and refrigerant pressure sensor

>> Repair open circuit or short to ground or short to power in harness or connectors.

8.CHECK INTERMITTENT INCIDENT

Refer to GI, "Intermittent Incident".

Is the inspection result normal?

YES >> Replace refrigerant pressure sensor. Refer to HA, "Removal and Installation".

NO >> Repair or replace.

On board refueling vapor recovery (ORVR)

Component Function Check 1.CHECK ORVR FUNCTION Check whether the following symptoms are present. Fuel odor from EVAP canister is strong. Cannot refuel/Fuel odor from the fuel filler opening i ...

Engine control system symptoms

Symptom Table SYSTEM - BASIC ENGINE CONTROL SYSTEM 1 - 6: The numbers refer to the order of inspection. (continued on next table) SYSTEM - ENGINE MECHANICAL & OTHER ...

Other materials:

Rear window defroster switch
To defrost the rear window glass, start the engine and push the rear window defroster switch on. The rear window defroster indicator light on the switch comes on. Push the switch again to turn the defroster off. The rear window defroster automatically turns off after approximately 15 m ...

Rear LH
REAR LH : Component Function Check 1.CHECK FUNCTION Select DOOR LOCK of BCM using CONSULT. Select DOOR LOCK in ACTIVE TEST mode. Touch ALL LOCK or ALL UNLK to check that it works normally. Is the inspection result normal? YES >> Door lock actuator is OK. NO >> Refer to DLK ...

Categories


© 2017-2026 Copyright www.niveguide.com
0.0052