Nissan Versa (N17): Door does not lock/unlock with door lock and unlock switch

Nissan Versa 2nd generation (N17) Service Manual / Body exterior, doors, roof & vehicle security / Door & lock (DLK) / Door does not lock/unlock with door lock and unlock switch

All door

ALL DOOR : Description

All doors do not lock/unlock using door lock and unlock switch.

ALL DOOR : Diagnosis Procedure

1.CHECK DOOR LOCK AND UNLOCK SWITCH

Check door lock and unlock switch.

Refer to DLK "Component Function Check".

Is the inspection result normal?

YES >> GO TO 2.

NO >> Repair or replace the malfunctioning parts.

2.CHECK DOOR LOCK ACTUATOR

Check front door lock assembly (driver side).

Refer to DLK "DOOR LOCK : Removal and Installation".

Is the inspection result normal?

YES >> GO TO 3.

NO >> Repair or replace the malfunctioning parts.

3.REPLACE BCM

  1. Replace BCM. Refer to BCS "Removal and Installation".
  2. Confirm the operation after replacement.

Is the result normal?

YES >> Inspection End.

NO >> Check intermittent incident. Refer to GI "Intermittent Incident".

Driver side

DRIVER SIDE : Description

Driver side door does not lock/unlock using door lock and unlock switch.

DRIVER SIDE : Diagnosis Procedure

1.CHECK DOOR LOCK ACTUATOR

Check front door lock assembly (driver side).

Refer to DLK "DRIVER SIDE : Component Function Check".

Is the inspection result normal?

YES >> GO TO 2.

NO >> Repair or replace the malfunctioning parts.

2.REPLACE BCM

  1. Replace BCM. Refer to BCS "Removal and Installation".
  2. Confirm the operation after replacement.

Is the result normal?

YES >> Inspection End.

NO >> Check intermittent incident. Refer to GI "Intermittent Incident".

Passenger side

PASSENGER SIDE : Description

Passenger side door does not lock/unlock using door lock and unlock switch.

PASSENGER SIDE : Diagnosis Procedure

1.CHECK DOOR LOCK ACTUATOR

Check front door lock assembly (passenger side).

Refer to DLK "PASSENGER SIDE : Component Function Check".

Is the inspection result normal?

YES >> GO TO 2.

NO >> Repair or replace the malfunctioning parts.

2.REPLACE BCM

  1.  Replace BCM. Refer to BCS "Removal and Installation".
  2.  Confirm the operation after replacement.

Is the result normal?

YES >> Inspection End.

NO >> Check intermittent incident. Refer to GI "Intermittent Incident".

Rear LH

REAR LH : Description

Rear LH side door does not lock/unlock using door lock and unlock switch.

REAR LH : Diagnosis Procedure

1.CHECK DOOR LOCK ACTUATOR

Check rear door lock assembly LH.

Refer to DLK "REAR LH : Component Function Check".

Is the inspection result normal?

YES >> GO TO 2.

NO >> Repair or replace the malfunctioning parts.

2.REPLACE BCM

Replace BCM. Refer to BCS "Removal and Installation".

Confirm the operation after replacement.

Is the result normal?

YES >> Inspection End.

NO >> Check intermittent incident. Refer to GI "Intermittent Incident".

Rear RH

REAR RH : Description

Rear RH side door does not lock/unlock using door lock and unlock switch.

REAR RH : Diagnosis Procedure

1.CHECK DOOR LOCK ACTUATOR

Check rear door lock assembly RH.

Refer to DLK "REAR RH : Component Function Check".

Is the inspection result normal?

YES >> GO TO 2.

NO >> Repair or replace the malfunctioning parts.

2.REPLACE BCM

  1. Replace BCM. Refer to BCS "Removal and Installation".
  2. Confirm the operation after replacement.

Is the result normal?

YES >> Inspection End.

NO >> Check intermittent incident. Refer to GI "Intermittent Incident".

Trunk lamp switch

Description Detects trunk open/close condition. Component Function Check 1.CHECK FUNCTION With CONSULT Check TRNK/HAT MNTR in Data Monitor mode with CONSULT.   Is the inspection ...

Door does not lock/unlock with driver side door lock knob or door key cylinder

Diagnosis Procedure 1.CHECK POWER DOOR LOCK OPERATION Check power door lock operation. Does door lock/unlock with door lock and unlock switch? YES >> GO TO 2. NO >> Refer to DLK " ...

Other materials:

P0731 1GR Incorrect ratio
Description This malfunction is detected when the A/T does not shift into 1GR position as instructed by TCM. This is not only caused by electrical malfunction (circuits open or shorted) but by mechanical malfunction such as control valve sticking, improper solenoid valve operation, etc. DTC ...

EPS System
EPS SYSTEM : System Description EPS control unit performs an arithmetical operation on data, such as steering wheel turning force (sensor signal) from the torque sensor, vehicle speed signal, etc. Then it generates an optimum assist torque signal to the EPS motor according to the drivi ...

Categories


© 2017-2025 Copyright www.niveguide.com
0.0088