Nissan Versa (N17): P0744 Torque converter

Nissan Versa 2nd generation (N17) Service Manual / Transmission & driveline / Transaxle & transmission (TM) / P0744 Torque converter

DTC Logic

DTC DETECTION LOGIC

DTC Trouble diagnosis name DTC detection condition Possible causes
P0744 Torque converter clutch circuit intermittent The torque converter slip speed is at or above a set value (40 rpm + (Vehicle speed / 2) continuously for 30 seconds or more under the following diagnosis conditions:

- Diagnosis conditions

- Selector lever: "D" position

- Accelerator pedal position: 1.0/8 or more

- Vehicle speed: 10 km/h (6 MPH) or more

- Engine speed: 450 rpm or more

- CVT fluid temperature: 20C (68F) ≤ CVT fluid temperature ≤ 180C (356F)

- Lockup command is being given (except for slip lockup).

- LU PRS: More than 0.2 MPa

- TCM power supply voltage: More than 11 V

- Torque converter clutch solenoid valve

- Control valve assembly

- Torque converter

DTC CONFIRMATION PROCEDURE

CAUTION: Be careful of the driving speed.

1.PREPARATION BEFORE OPERATION 1

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.

>> GO TO 2.

2.PREPARATION BEFORE OPERATION 2

With CONSULT

  1. Start the engine.
  2. Select "Data Monitor" in "TRANSMISSION".
  3. Select "FLUID TEMP".
  4. Confirm that the CVT fluid temperature is in the range below.

FLUID TEMP : 20C (68F) or more

With GST

  1. Start the engine.
  2. Set the CVT fluid to 20C (68F) or more.

    NOTE: When the ambient temperature is 20C (68F), the CVT fluid usually increases to 50 to 80C (122 to 176F) with driving in an urban area for approximately 10 minutes.

Is the CVT fluid 20C (68F) or more?

YES >> GO TO 3.

NO >> 1. Warm the transaxle.  2. GO TO 3.

3.CHECK DTC DETECTION

  1. Drive the vehicle.
  2. Maintain the following conditions for 40 seconds or more.

Selector lever : "D" position

Accelerator pedal position : 1.0/8 or more

Vehicle speed : 40 km/h (25 MPH) or more

    3.   Stop the vehicle.

    4.   Check the first trip DTC.

Is "P0744" detected?

YES >> Go to TM "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK LINE PRESSURE

Perform line pressure test. Refer to TM "Work Procedure".

Is the inspection result normal?

YES >> GO TO 2.

NO >> Repair or replace the malfunction items.

2.CHECK TORQUE CONVERTER CLUTCH SOLENOID VALVE

  1. Turn ignition switch OFF.
  2. Disconnect CVT unit connector.
  3. Check torque converter clutch solenoid valve. Refer to TM "Component Inspection (Torque Converter Clutch Solenoid Valve)".

Is the inspection result normal?

YES >> GO TO 3.

NO >> Repair or replace the malfunction items.

3.CHECK INTERMITTENT INCIDENT

Refer to GI "Intermittent Incident".

Is the inspection result normal?

YES >> Replace the transaxle assembly. Refer to TM, "Removal and Installation".

NO >> Repair or replace the malfunction items.

Component Inspection (Torque Converter Clutch Solenoid Valve)

1.CHECK TORQUE CONVERTER CLUTCH SOLENOID VALVE

Check resistance between CVT unit connector terminal and ground.  

Is the inspection result normal?

YES >> INSPECTION END

NO >> There is a malfunction of torque converter clutch solenoid valve. Replace transaxle assembly.

Refer to TM "Removal and Installation".

Other materials:

Precautions when starting and driving
WARNING Do not leave children or adults who would normally require the assistance of others alone in your vehicle. Pets should also not be left alone. They could accidentally injure themselves or others through inadvertent operation of the vehicle. Also, on hot, sunny days, tempera ...

Side oil seal
Removal and Installation REMOVAL Remove front drive shaft from transaxle assembly. Refer to FAX, "Removal and Installation". Remove differential side oil seal (1) using suitable tool. CAUTION: Do not damage transaxle case and clutch housing. INSTALLATION   & ...

Categories


© 2017-2025 Copyright www.niveguide.com
0.0072