Nissan Versa (N17): P0112, P0113 IAT sensor

DTC Logic

DTC DETECTION LOGIC

DTC No. Trouble diagnosis name DTC detecting condition Possible cause
P0112 Intake air temperature sensor circuit low input An excessively low voltage from the sensor is sent to ECM.
  • An excessively high voltage from the sensor is sent to ECM.
  • Intake air temperature sensor
P0113 Intake air temperature sensor circuit high input An excessively high voltage from the sensor is sent to ECM.

DTC CONFIRMATION PROCEDURE

1.PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.
  2. Turn ignition switch ON.
  3. Turn ignition switch OFF and wait at least 10 seconds.

>> GO TO 2.

2.PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON and wait at least 5 seconds.
  2. Check 1st trip DTC.

Is 1st trip DTC detected?

YES >> Go to EC, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK GROUND CONNECTION

  1. Turn ignition switch OFF.
  2. Check ground connection E. Refer to Ground Inspection in G, "Circuit Inspection".

Is the inspection result normal?

YES >> GO TO 2.

NO >> Repair or replace ground connection.

2.CHECK INTAKE AIR TEMPERATURE SENSOR POWER SUPPLY CIRCUIT

  1. Disconnect mass air flow (MAF) sensor (with intake air temperature sensor) harness connector.
  2. Turn ignition switch ON.
  3. Check the voltage between mass air flow sensor harness connector and ground.

CHECK INTAKE AIR TEMPERATURE SENSOR POWER SUPPLY CIRCUIT

Is the inspection result normal?

YES >> GO TO 3.

NO >> Repair open circuit or short to ground or short to power in harness or connectors.

3.CHECK INTAKE AIR TEMPERATURE SENSOR GROUND CIRCUIT FOR OPEN AND SHORT

  1. Turn ignition switch OFF.
  2. Disconnect ECM harness connector.
  3. Check the continuity between mass air flow sensor harness connector and ECM harness connector.

CHECK INTAKE AIR TEMPERATURE SENSOR GROUND CIRCUIT FOR OPEN AND SHORT

    4.   Also check harness for short to ground and short to power.

Is the inspection result normal?

YES >> GO TO 4.

NO >> Repair open circuit or short to ground or short to power in harness or connectors.

4.CHECK INTAKE AIR TEMPERATURE SENSOR

Refer to EC, "Component Inspection".

Is the inspection result normal?

YES >> GO TO 5.

NO >> Replace mass air flow sensor (with intake air temperature sensor). Refer to EM, "Removal and Installation".

5.CHECK INTERMITTENT INCIDENT

Refer to GI, "Intermittent Incident".

>> INSPECTION END

Component Inspection

1.CHECK INTAKE AIR TEMPERATURE SENSOR

  1. Turn ignition switch OFF.
  2. Disconnect mass air flow sensor harness connector.
  3. Check resistance between mass air flow sensor terminals as per the following.

CHECK INTAKE AIR TEMPERATURE SENSOR

Is the inspection result normal?

YES >> INSPECTION END

NO >> Replace mass air flow sensor (with intake air temperature sensor). Refer to EM, "Removal and Installation".

Other materials:

Security systems (if so equipped)
Your vehicle has one type of security systems: NISSAN Vehicle Immobilizer System NISSAN vehicle immobilizer system The NISSAN Vehicle Immobilizer System will not allow the engine to start without the use of a registered key. If the engine fails to start using a registered key (for ex ...

Service data and specifications (SDS)
General Specifications Engine type HR16DE Type of clutch control Hydraulic Clutch disc Facing size (Outer dia. × Inner dia. × Thickness) 200 × 140 × 3.1 (7.87 × 5.51 × 0.122) Recommended clutch fluid Refer to M ...

Categories


© 2017-2025 Copyright www.niveguide.com
0.0077