Nissan Versa (N17): Battery replacement

Nissan Versa 2nd generation (N17) Owners Manual / Do-it-yourself / Battery replacement

CAUTION

Be careful not to allow children to swallow the battery or removed parts.

Key fob (if so equipped)

Key fob (if so equipped)

Replace the battery in the key fob as follows: 1. Remove the screw A .

2. Insert a small screwdriver into the slit of the corner B and twist it to separate the upper part from the lower part. Use a cloth to protect the casing.

3. Replace the battery with a new one.

  • Do not touch the internal circuit and electric terminals as doing so could cause a malfunction.
  • Make sure that the + side faces the bottom of the case C .

Recommended battery: CR1620 or equivalent.

4. Close the lid and install the screw securely.

5. Operate the buttons to check its operation.

If you need assistance for replacement, it is recommended that you visit a NISSAN dealer for this service.

If the battery is removed for any reason other than replacement, perform step 5.

  • An improperly disposed battery can hurt the environment. Always confirm local regulations for battery disposal.
  • The key fob is water-resistant; however, if it does get wet, immediately wipe completely dry.
  • The operational range of the key fob extends to approximately 33 ft (10 m) from the vehicle. This range may vary with conditions.

Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device.

FCC Notice: For USA: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note:

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

For Canada: This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Key fob (if so equipped)

NISSAN Intelligent Key (if so equipped)

Replace the battery in the Intelligent Key as follows: 1. Remove the mechanical key from the Intelligent Key.

2. Insert a small flathead screwdriver A into the slit B of the corner and twist it to separate the upper part from the lower part. Place a cloth over the screwdriver to protect the casing.

NISSAN Intelligent Key (if so equipped)

3. Replace the battery with a new one.

Recommended battery: CR2025 or equivalent.

  • Do not touch the internal circuit and electric terminals as doing so could cause a malfunction.
  • Hold the battery by the edges. Holding the battery across the contact points will seriously deplete the storage capacity.
  • Make sure that the + side faces the bottom of the lower part.

4. Close the lid securely as illustrated with C and D .

5. Operate the buttons to check the operation.

If you need assistance for replacement, it is recommended that you visit a NISSAN dealer for this service.

FCC Notice: For USA: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note:

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

For Canada: This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Fuses

If any electrical equipment does not operate, check for an open fuse. Fuses are used in the passenger compartment. Spare fuses are provided and can be found in the passenger compartment fuse ...

Other materials:

Line pressure test
Work Procedure INSPECTION Check the engine oil level. Replenish if necessary. Refer to LU "Inspection". Check for CVT fluid leaks. Refer to TM "Inspection". Drive for about 10 minutes to warm up the vehicle so that the CVT fluid temperature is 50 to 80C (122 to ...

Front seat
DRIVER SIDE DRIVER SIDE : Exploded View WITH REMOVABLE HEADREST 1. Armrest (if equipped) 2. Seat cushion outer finisher (RH) 3. Seat belt buckle 4. Seat cushion trim 5. Seat cushion pad 6. Seat cushion frame 7. Seat cushion outer finisher (LH) 8. Lift lever (if equipped) 9. Lift lever c ...

Categories


© 2017-2025 Copyright www.niveguide.com
0.008