Nissan Versa (N17): P0711 Transmission fluid temperature sensor A

Nissan Versa 2nd generation (N17) Service Manual / Transmission & driveline / Transaxle & transmission (TM) / P0711 Transmission fluid temperature sensor A

DTC Logic

DTC DETECTION LOGIC

DTC Trouble diagnosis name DTC detection condition Possible causes
P0711 Transmission Fluid Temperature Sensor "A" Circuit Range/ Performance Under the following diagnosis conditions, A/T fluid temperature does not rise to 15C (59F) after driving for a certain period of time with the TCM-received fluid temperature sensor value between −40C (−40F) and 14C (57.2F).

- Diagnosis condition

  • Selector lever: "D" position
  • Vehicle speed: 10 km/h (7 MPH) or more
  • Engine speed: 450 rpm or more
  • Accelerator pedal position: 1.0/8 or more
  • TCM power supply voltage: More than 11 V
 A/T fluid temperature sensor
When the condition of the final judgment is satisfied after satisfying that of the provisional judgment:
  • Provisional judgment: All of the following conditions are satisfied within 2 seconds after the ignition switch is turned ON.
  • U0073, U0100, P0712 and P0713 are not detected.
  • CAN communication is normal.
  • TCM power supply voltage: More than 11 V
  • The difference between A/T fluid temperature and engine coolant temperature is 38C (100.4F) or more, or −27C (−16.6F) or less.
  • Final judgment: When all of the following conditions are satisfied and this state is maintained for 300 seconds:
  • ECM is normal.
  • Provisional judgment is satisfied.
 A/T fluid temperature sensor

DTC CONFIRMATION PROCEDURE

CAUTION: Always drive vehicle at a safe speed.

1.PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.

>> GO TO 2.

2.CHECK A/T FLUID TEMPERATURE SENSOR FUNCTION

With CONSULT

  1. Cool the engine.
  2. Turn ignition switch ON.

CAUTION: Never start the engine.

  1. Select "FLUID TEMP" in "Data Monitor" in "TRANSMISSION".
  2. Select "COOLANT TEMP/S" in "Data Monitor" in "ENGINE".
  3. Check temperature difference between A/T fluid and engine coolant.

With GST

  1. Complete engine diagnoses P0111, P0116, and P0196.
  2. After starting the engine start, run the engine at idle for 5 minutes.
  3. Check the DTC.

Is the temperature calculated by subtracting engine coolant temperature from A/T fluid temperature more than 38C (100.4F) or is it less than −27C (−16.6F)? (With CONSULT)/Is "P0711" detected? (With GST)

YES >> Go to TM, "Diagnosis Procedure".

NO-1 [With CONSULT: "FLUID TEMP" is 15C (59F) or more]>>INSPECTION END

NO-2 [With CONSULT: "FLUID TEMP" is 14C (57.2F) or less]>>GO TO 3.

NO-3 (With GST)>>GO TO 3.

3.CHECK DTC DETECTION

With CONSULT

  1. Select "SLCT LVR POSI", "VHCL/S SE-AT", "ACCELE POSI", "FLUID TEMP" in "Data Monitor" in "TRANSMISSION".
  2. Record A/T fluid temperature.
  3. Start the engine and wait for at least 3 minutes.
  4. Drive the vehicle for the total minuets specified in the Driving time column below with the following conditions satisfied.

SLCT LVR POSI : D

VHCL/S SE-AT : 10 km/h (7 MPH) or more

ACCELE POSI : 1.0/8 or more

    5.   Perform "Self Diagnostic Results" in "TRANSMISSION".

With GST

  1. Cool the engine.

  2. Start the engine and wait for at least 3 minutes.

  3. Drive the vehicle and maintain the following conditions for 21 minutes or more.

Selector lever : D position

Vehicle speed : 10 km/h (7 MPH) or more

Accelerator pedal opening : 1.0/8 or more

Check the DTC.

Is "P0711" detected?

YES >> Go to TM, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK A/T FLUID TEMPERATURE SENSOR

  1. Turn ignition switch OFF.
  2. Disconnect the A/T unit connector.
  3. Check the A/T fluid temperature sensor. Refer to TM, "Component Inspection (A/T Fluid Temperature Sensor)".

Is the check result normal?

YES >> Check intermittent incident. Refer to GI "Intermittent Incident".

NO >> Repair or replace the malfunctioning parts.

Component Inspection (A/T Fluid Temperature Sensor)

1.CHECK A/T FLUID TEMPERATURE SENSOR

Measure the resistance between the A/T unit connector terminals. 

Is the check result normal?

YES >> INSPECTION END

NO >> There is a malfunction of the A/T fluid temperature sensor. Replace the transaxle assembly. Refer to TM, "Removal and Installation".

P0706 Transmission range sensor A

DTC Logic DTC DETECTION LOGIC DTC Trouble diagnosis name DTC detection condition Possible causes P0706 Transmission Range Sensor "A" Circuit Range/Performance The ...

P0712 Transmission fluid temperature sensor A

DTC Logic DTC DETECTION LOGIC DTC Trouble diagnosis name DTC detection condition Possible causes P0712 Transmission Fluid Temperature Sensor "A" Circuit Low Under ...

Other materials:

Air bags, seat belts and child restraints
1. Supplemental air bag modules 2. Roof-mounted curtain side-impact and rollover supplemental air bag 3. Front seat-mounted side-impact supplemental air bag 4. Front seat belt with pretensioner(s) and shoulder height adjuster 5. Head restraints/headrests 6. Rear seat belts 7. LATCH (Low ...

Clutch pedal
Inspection and Adjustment 1.   Check to see if the master cylinder rod end moves freely. It should not be bound by the clutch pedal. a. If the rod end does not move freely, remove the rod end and check for deformation or damage on the rod end. Leave the rod end removed ...

Categories


© 2017-2026 Copyright www.niveguide.com
0.0061