Description
This malfunction is detected when the A/T does not shift into 3GR position as instructed by TCM. This is not only caused by electrical malfunction (circuits open or shorted) but by mechanical malfunction such as control valve sticking, improper solenoid valve operation, etc.
DTC Logic
DTC DETECTION LOGIC
DTC | Trouble diagnosis name | DTC detection condition | Possible causes |
P074B | Unable to Engage Gear 3 | Under the following diagnosis
conditions, the gear ratio is
3.033 or more continuously for
2 seconds or more. - Diagnosis condition - Shifting is not in progress. - Input speed: 300 rpm or more - Output speed: 300 rpm or more - Engine speed: (Input speed - 50 rpm) or more - Selector lever: D position - Gear: 3GR - Throttle position: 0.7/8.0 or more |
- Low clutch solenoid valve - Control valve assembly |
DTC CONFIRMATION PROCEDURE
CAUTION:
1.PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT
NOTE: "3RD GR FNCTN P0731" can be used in this diagnosis.
Selector lever : D position (O/D OFF)
Gear : 3GR
Accelerator pedal position : 0.7/8 or more
Vehicle speed : 20 km/h (13 MPH) or more
3. Keep the current driving status for 2 seconds or more if CONSULT screen changes from "OUT OFCONDITION" to "TESTING".
CAUTION: When "TESTING" is not indicated on CONSULT for a long time, check "Self Diagnostic Results" in "TRANSMISSION". When a DTC other than "P074B" is detected, check the DTC. Refer to TM, "DTC Index".
With GST
1. Drive vehicle and maintain the following conditions for 2 seconds or more.
Selector lever : D position (O/D OFF)
Gear : 3GR
Accelerator pedal position : 0.7/8 or more
Vehicle speed : 20 km/h (13 MPH) or more
2. Check the first trip DTC.
Is "OUT OF CONDITION", "STOP VEHICLE", or "COMPLETED RESULT NG" displayed? / Is "P074B" detected?
YES-1 (OUT OF CONDITION.)>>Perform "step 2" again.
YES-2 (STOP VEHICLE.)>>GO TO 3.
YES-3 (COMPLETED RESULT NG)>>Go to TM "Diagnosis Procedure".
YES-4 ("P074B" is detected.)>>Go to TM "Diagnosis Procedure".
NO >> GO TO 3.
3.CHECK SYMPTOM
>> INSPECTION END
Diagnosis Procedure
1.MALFUNCTION CAUSE SIMULATION TEST
Refer to GI, "Intermittent Incident".
Is the check result normal?
YES >> Replace the transaxle assembly. Refer to TM, "Removal and Installation".
NO >> Repair or replace the malfunctioning parts.
Description This malfunction is detected when the A/T does not shift into 2GR position as instructed by TCM. This is not only caused by electrical malfunction (circuits open or shorted) but by m ...
Description This malfunction is detected when the A/T does not shift into 4GR position as instructed by TCM. This is not only caused by electrical malfunction (circuits open or shorted) but by ...
Positive crankcase ventilation
Inspection
1.CHECK PCV VALVE
With engine running at idle, remove PCV valve from rocker cover. A
properly working valve makes a hissing noise as air passes through
it. A strong vacuum should be felt immediately when a finger is
placed over valve inlet.
Is the inspection result normal?
YES &g ...
Front bumper
Exploded View
1. Front bumper side bracket (RH) 2. Front bumper reinforcement 3. Front
bumper energy absorber
4. Front bumper fascia finisher (RH)
(If equipped)
5. Front bumper fascia 6. Fog lamp finisher (RH) (if
equipped)
7. Tow cover 8. License plate bracket 9. Under cover 10. Fog lam ...