TYPE A : Description
Transmits the parking brake switch signal to the combination meter.
TYPE A : Component Function Check
1.COMBINATION METER INPUT SIGNAL
1. Select "METER/M&A" on CONSULT.
2. Monitor "PKB SW" of "DATA MONITOR" while applying and releasing the parking brake.
PKB SW
Parking brake depressed : ON
Parking brake released : OFF
Is the inspection result normal?
YES >> Inspection End.
NO >> Refer to WCS "TYPE A : Diagnosis Procedure".
TYPE A : Diagnosis Procedure
Regarding Wiring Diagram information, refer to WCS "Wiring Diagram".
1.CHECK COMBINATION METER INPUT SIGNAL
1. Turn ignition switch ON.
2. Check the voltage between combination meter harness connector and ground.
Is the inspection result normal?
YES >> Inspection End.
NO >> GO TO 2.
2.CHECK PARKING BRAKE SWITCH SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect combination meter connector and parking brake switch connector.
3. Check continuity between combination meter harness connector and parking
brake switch harness connector.
4. Check continuity between combination meter harness connector and ground.

Is the inspection result normal?
YES >> Inspection End.
NO >> Repair harness or connector.
TYPE A : Component Inspection
1.CHECK PARKING BRAKE SWITCH
Check continuity between parking brake switch terminal 1 and switch case
ground.

Is the inspection result normal?
YES >> Inspection End.
NO >> Replace parking brake switch.
TYPE B : Description
Transmits the parking brake switch signal to the combination meter.
TYPE B : Component Function Check
1.COMBINATION METER INPUT SIGNAL
1. Select "METER/M&A" on CONSULT.
2. Monitor "PKB SW" of "DATA MONITOR" while applying and releasing the parking brake.
PKB SW
Parking brake depressed : ON
Parking brake released : OFF
Is the inspection result normal?
YES >> Inspection End.
NO >> Refer to WCS "TYPE B : Diagnosis Procedure".
TYPE B : Diagnosis Procedure
Regarding Wiring Diagram information, refer to WCS "Wiring Diagram".
1.CHECK COMBINATION METER INPUT SIGNAL
1. Turn ignition switch ON.
2. Check the voltage between combination meter harness connector and ground.
Is the inspection result normal?
YES >> Inspection End.
NO >> GO TO 2.
2.CHECK PARKING BRAKE SWITCH SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect combination meter connector and parking brake switch connector.
3. Check continuity between combination meter harness connector and parking
brake switch harness connector.
4. Check continuity between combination meter harness connector and ground.

Is the inspection result normal?
YES >> Inspection End.
NO >> Repair harness or connector.
TYPE B : Component Inspection
1.CHECK PARKING BRAKE SWITCH
Check continuity between parking brake switch terminal 1 and switch case
ground.

Is the inspection result normal?
YES >> Inspection End.
NO >> Replace parking brake switch.
SYMPTOM DIAGNOSIS
Key switch signal circuit (without
intelligent key)Description Transmits a key switch signal to the BCM. Component Function Check 1. CHECK BCM INPUT SIGNAL Select "DATA MONITOR" for "BCM" and check the "KEY ON SW" monitor value. KEY ON SW ...

Description The parking brake warning buzzer sounds continuously during vehicle travel though the parking brake is released. The parking brake warning buzzer does not sound at all even thou ...
Oil cooler
Exploded View
1. Radiator hose (upper) 2. Hose clamp 3. Radiator hose (lower)
4. Hose clamp 5. Water hose 6. Oil cooler
7. Connector bolt 8. Water hose 9. Oring
A. To radiator (upper side) B. To radiator (lower side) 10. Relief valve
Removal and Installation
REMOVAL
NOTE:
When removing co ...
PRECAUTIONS
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER"
The Supplemental Restraint System such as "AIR BAG" and "SEAT BELT PRE-TENSIONER",
used along
with a front seat belt, helps to reduce the risk or severity of injury to the
driver and ...