Nissan Versa (N17): Rear seat

Exploded View - Fixed Seatback

FIXED SEATBACK

1. Headrest holder (locked) 2. Headrest holder (free) 3. Rear seatback assembly 4. Seatback trim 5. Seatback pad 6. LATCH bracket (RH) 7. Seat cushion assembly 8. Seat cushion trim 9. Seat cushion pad 10. Seat cushion hook 11. LATCH bracket (LH) 12. Headrest

Exploded View - 60:40 Split Seatback

60:40 SPLIT SEATBACK

1. Headrest 2. Rear seatback assembly (RH) 3. Headrest holder (free) 4. Headrest holder (locked) 5. Rear seatback frame (RH) 6. Seatback latch assembly (RH) 7. Seatback trim (RH) 8. Seatback pad (RH) 9. Rear seat bolster (RH) 10. Seatback hinge finisher 11. Seat cushion assembly 12. Seat cushion trim 13. Seat cushion pad 14. Seat cushion hook 15. Seatback hinge assembly 16. Rear seat bolster (LH) 17. Seatback pad (LH) 18. Seatback trim (LH) 19. Seatback latch assembly (LH) 20. Seatback striker 21. Rear seatback frame (LH) 22. Rear seatback assembly (LH) A. Seatback hinge finisher clips

Removal and Installation - Seat Cushion Assembly

REMOVAL

    1.  Lift up the seat cushion assembly close to the front edge (B) to release it from the seat cushion hooks (A) (one for each side) and remove the seat cushion assembly.

: Front

INSTALLATION

Installation is in the reverse order of removal.

Removal and Installation - Fixed Seatback

REMOVAL

1. Remove the seat cushion assembly. Refer to SE "Removal and Installation - Seat Cushion Assembly".
2. Remove the rear seat belt D-ring anchors (LH/RH). Refer to SB "Exploded View".
3. Remove the two seatback bolts.
4. Lift the rear seatback assembly upward and disengage the seatback frame (A) from body hook (B) and remove the rear seatback assembly.

INSTALLATION

Installation is in the reverse order of removal.

• Tighten the rear seatback assembly bolts to specification. Refer to SE "Exploded View - Fixed Seatback".
• Tighten the rear seat belt D-ring anchors to specification. Refer to SB"Exploded View".

Removal and Installation - 60:40 Split Seatback

REMOVAL

1. Place the rear seatback assembly in the folded down position.
2. Release the hook fasteners (A) in the lower corners of the rear seatback assembly.
3. Remove the rear seatback assembly bolts (B) from the seatback hinge assembly (1), then remove the rear seatback assembly.

INSTALLATION

Installation is in the reverse order of removal.

Tighten the rear seatback assembly bolts to specification. Refer to SE "Exploded View - 60:40 Split Seatback".

Removal and Installation - Seatback Hinge Assembly

1. Remove the seat cushion assembly. Refer to SE "Removal and Installation - Seat Cushion Assembly".
2. Remove the rear seatback assemblies (LH/RH). Refer to SE "Removal and Installation - 60:40 Split Seatback"
3. Remove the rear seat bolsters (LH/RH). Refer to SE "Removal and Installation - Rear Seat Bolster"
4. Remove the bolts and the seatback hinge assembly.

INSTALLATION

Installation is in the reverse order of removal.

• Tighten the seatback hinge assembly bolts to specification. Refer to SE "Exploded View - 60:40 Split Seatback".

Removal and Installation - Rear Seat Bolster

REMOVAL

1. Remove the seat cushion assembly. Refer to SE "Removal and Installation - Seat Cushion Assembly".
2. Remove the bolt at bottom of rear seat bolster.
3. Lift the rear seat bolster to remove.

INSTALLATION

Installation is in the reverse order of removal.

• Tighten rear seat bolster bolt to specification. Refer to SE "Exploded View - 60:40 Split Seatback".

Removal and Installation - Seat Cushion Hook

REMOVAL

1. Remove the seat cushion assembly. Refer to SE "Removal and Installation - Seat Cushion Assembly".
2. Release the seat cushion hook pawls as shown and remove.

CAUTION: Before removing/installing the seat cushion hook, check its orientation (front/rear).

INSTALLATION

Installation is in the reverse order of removal.

UNIT DISASSEMBLY AND ASSEMBLY