Exploded View
1. Strut assembly 2. Coil spring 3. Bound bumper 4. Spring upper seat 5. Strut mounting bearing 6. Piston rod lock nut 7. Strut mounting insulator 8. Stopper insulator 9. Stopper insulator lock nut
REMOVAL
INSTALLATION
Installation is in the reverse order of removal.
CAUTION: Do not reuse stopper insulator lock nut.
DISASSEMBLY
CAUTION: Do not damage strut assembly piston rod when removing components from strut assembly.
Tool number : ST35652000 ( - )
CAUTION: When installing the Tool to strut assembly, wrap a shop cloth around strut to protect from damage.
CAUTION: Be sure the tool is securely attached to the coil spring before compressing coil spring.
CAUTION: Loosen while making sure coil spring attachment position does not move.
Tool number : ST35652000 ( - )
9. If necessary, remove strut mounting bearing (1) from spring upper seat (2), using a Tool (A).
Tool number : KV10106700 ( - )
CAUTION: Do not disassemble the strut mounting bearing unless damage exists.
10. Perform inspection after disassembly. Refer to FSU "Inspection and Adjustment".
INSPECTION AFTER DISASSEMBLY
Strut Inspection
Check the following:
Strut Mounting Insulator and Rubber Parts Inspection
Check strut mounting insulator for cracks and rubber parts for wear. Replace it if malfunction is detected.
Coil Spring Inspection
Check coil spring for cracks, wear or damage, and replace it if necessary.
ASSEMBLY
1. Install Tool (A) to strut and secure it in a vise.
Tool number : ST35652000 ( - )
CAUTION: When installing the strut attachment to strut assembly, wrap a shop cloth around strut to protect from damage.
2. Apply soapy water to bound bumper.
CAUTION: Do not use machine oil.
3. Insert bound bumper into spring upper seat.
4. Compress coil spring using a spring compressor (commercial service tool), and install it onto strut assembly.
CAUTION:
Compress coil spring.
5. Install strut mounting bearing, spring upper seat, and bound bumper as a set.
6. Secure piston rod tip so that piston rod does not turn, then tighten piston rod lock nut with specified torque.
7. Gradually release a spring compressor, and remove coil spring.
CAUTION: Loosen while making sure coil spring attachment position does not move.
8. Remove the Tool (A) from strut assembly.
Tool number : ST35652000 ( - )
9. Install strut mounting insulator.
CAUTION:
NOTE:
(A) : 20 - 30 mm (0.79 - 1.18 in)
3. Position the drilled hole downward and drain oil by moving the piston rod several times.
CAUTION: Dispose of drained oil according to the law and local regulations.
Inspection and Adjustment INSPECTION Make sure the mounting conditions (looseness, back lash) of each component and component conditions (wear, damage) are normal. LOWER BALL JOINT END PLAY ...
Exploded View 1. Front suspension member 2. Transverse link Removal and Installation REMOVAL Remove the wheel and tire assembly using power tool. Refer to WT "Adjustment". ...
U0300 Can communication data
Description
The amount of data transmitted from each control unit is read.
DTC Logic
DTC DETECTION LOGIC
DTC
Trouble diagnosis name
DTC detection condition
Possible causes
U0300
Internal Control Module Software
Incompatibility
When the amount of data transmitt ...
Structure and operation
TRANSAXLE
TRANSAXLE : Cross-Sectional View
1. Converter housing 2. Oil pump 3. Counter drive gear
4. Control valve 5. Oil pan 6. Primary pulley
7. Steel belt 8. Secondary pulley 9. Planetary gear (auxiliary gearbox)
10. Side cover 11. Transaxle case 12. Differential case
13. Final gear ...