Nissan Versa (N17): Door lock and unlock switch

Nissan Versa 2nd generation (N17) Service Manual / Body exterior, doors, roof & vehicle security / Door & lock (DLK) / Door lock and unlock switch

DRIVER SIDE

DRIVER SIDE : Description

Transmits door lock/unlock operation to BCM.

DRIVER SIDE : Component Function Check

1.CHECK FUNCTION

With CONSULT

Check CDL LOCK SW, CDL UNLOCK SW in Data Monitor mode with CONSULT.  

Is the inspection result normal?

YES >> Door lock and unlock switch is OK.

NO >> Refer to DLK "DRIVER SIDE : Diagnosis Procedure".

DRIVER SIDE : Diagnosis Procedure

Regarding Wiring Diagram information, refer to DLK "Wiring Diagram".

1.CHECK POWER WINDOW SWITCH OUTPUT SIGNAL

  1. Turn ignition switch ON.
  2. Check voltage at the main power window and door lock/unlock switch connector when the switch (driver side) is turned to "LOCK" or "UNLOCK".                               

Is the inspection result normal?

YES >> GO TO 5

NO >> GO TO 2

2.CHECK POWER WINDOW SWITCH GROUND

  1. Turn ignition switch OFF.
  2. Disconnect main power window and door lock/unlock switch connector.
  3. Check continuity between main power window and door lock/unlock switch connector and ground.

Is the inspection result normal?

YES >> GO TO 3

NO >> Repair or replace harness.

3.CHECK POWER WINDOW SWITCH

Check continuity between main power window and door lock/unlock switch terminals.  

Is the inspection result normal?

YES >> GO TO 4

NO >> Replace main power window and door lock/unlock switch. Refer to DLK "Removal and Installation".

4.CHECK POWER WINDOW SWITCH CIRCUITS

  1. Disconnect BCM connector.
  2. Check continuity between BCM connector and main power window and door lock/unlock switch connector.
  3. Check continuity between BCM connector and ground.                   

Is the inspection result normal?

YES >> GO TO 5

NO >> Repair or replace harness.

5.CHECK INTERMITTENT INCIDENT

Refer to GI "Intermittent Incident".

>> Inspection End.

PASSENGER SIDE

PASSENGER SIDE : Description

Transmits door lock/unlock operation to BCM.

PASSENGER SIDE : Component Function Check

1.CHECK FUNCTION

With CONSULT

Check CDL LOCK SW, CDL UNLOCK SW in Data Monitor mode with CONSULT.

Is the inspection result normal?

YES >> Door lock and unlock switch is OK.

NO >> Refer to DLK "PASSENGER SIDE : Diagnosis Procedure".

PASSENGER SIDE : Diagnosis Procedure

Regarding Wiring Diagram information, refer to DLK "Wiring Diagram".

1.CHECK POWER WINDOW SWITCH OUTPUT SIGNAL

  1. Turn ignition switch ON.
  2. Check voltage at the power window and door lock/unlock switch RH connector when the switch (passenger side) is turned to "LOCK" or "UNLOCK".              

Is the inspection result normal?

YES >> GO TO 5

NO >> GO TO 2

2.CHECK POWER WINDOW SWITCH GROUND

  1. Turn ignition switch OFF.
  2. Disconnect power window and door lock/unlock switch RH connector.
  3. Check continuity between power window and door lock/unlock switch RH connector and ground.  

Is the inspection result normal?

YES >> GO TO 3

NO >> Repair or replace harness.

3.CHECK POWER WINDOW SWITCH

Check continuity between power window and door lock/unlock switch RH terminals. 

Is the inspection result normal?

YES >> GO TO 4

NO >> Replace power window and door lock/unlock switch RH.

4.CHECK POWER WINDOW SWITCH CIRCUITS

  1. Disconnect BCM connector.
  2. Check continuity between BCM connector and power window and door lock/unlock switch RH connector.
  3. Check continuity between BCM connector and ground.                       

Is the inspection result normal?

YES >> GO TO 5

NO >> Repair or replace harness.

5.CHECK INTERMITTENT INCIDENT

Refer to GI "Intermittent Incident".

>> Inspection End.

Door switch

Description Detects door open/close condition. ...

Key cylinder switch

Description When the mechanical key is inserted and turned into the front door lock key cylinder switch LH, the switch transmits the LOCK or UNLOCK signal directly to the BCM. ...

Other materials:

Vehicle speed sensing auto lock operation does not operate
Diagnosis Procedure 1.CHECK AUTOMATIC LOCK/UNLOCK SELECT SETTING IN WORK SUPPORT Select DOOR LOCK of BCM using CONSULT. Select AUTOMATIC LOCK/UNLOCK SELECT in WORK SUPPORT mode. Check AUTOMATIC LOCK/UNLOCK SELECT setting in WORK SUPPORT. Refer to BCS "DOOR LOCK : CONSULT Function ( ...

Hazard function
Description Perform answer-back for each operation with number of blinks. Component Function Check 1.CHECK FUNCTION Check hazard warning lamp ("FLASHER") in Active Test. Is the inspection result normal? YES >> Hazard warning lamp circuit is OK. NO >> Refer to DLK "Diagnosis ...

Categories


© 2017-2025 Copyright www.niveguide.com
0.0055