Nissan Versa (N17): Power window motor

Nissan Versa 2nd generation (N17) Service Manual / Body exterior, doors, roof & vehicle security / Power window control system (PWC) / Power window motor

Driver side

DRIVER SIDE : Component Function Check

1. CHECK FUNCTION

Check front power window motor LH operation with power window main switch.

Is the inspection result normal?

YES >> Inspection End.

NO >> Refer to PWC "DRIVER SIDE : Diagnosis Procedure".

DRIVER SIDE : Diagnosis Procedure

Regarding Wiring Diagram information, refer to PWC "Wiring Diagram".

1.CHECK FRONT POWER WINDOW MOTOR LH INPUT SIGNAL

1. Turn ignition switch OFF.

2. Disconnect front power window motor LH connector.

3. Turn ignition switch ON.

4. Check voltage between front power window motor LH harness connector and ground.

Is the inspection result normal?

YES >> Replace front power window motor LH.

NO >> GO TO 2.

2.CHECK FRONT POWER WINDOW MOTOR LH CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect power window main switch connector.

3. Check continuity between power window main switch harness connector and front power window motor LH harness connector.

4. Check continuity between power window main switch harness connector and ground.

Is the inspection result normal?

YES >> Replace power window main switch. Refer to PWC "Removal and Installation".

NO >> Repair or replace harness.

Passenger side

PASSENGER SIDE : Component Function Check

1. CHECK FUNCTION

Check front power window motor RH operation with power window main switch or front power window switch RH.

Is the inspection result normal?

YES >> Inspection End.

NO >> Refer to PWC "PASSENGER SIDE : Diagnosis Procedure".

PASSENGER SIDE : Diagnosis Procedure

Regarding Wiring Diagram information, refer to PWC "Wiring Diagram".

1.CHECK FRONT POWER WINDOW MOTOR RH INPUT SIGNAL

1. Turn ignition switch OFF.

2. Disconnect front power window motor RH connector.

3. Turn ignition switch ON.

4. Check voltage between front power window motor RH harness connector and ground.

Is the inspection result normal?

YES >> Replace front power window motor RH.

NO >> GO TO 2.

2.CHECK FRONT POWER WINDOW MOTOR RH CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect front power window switch RH connector.

3. Check continuity between front power window switch RH harness connector and front power window motor RH harness connector.

4. Check continuity between front power window switch RH harness connector and ground.

Is the inspection result normal?

YES >> Replace front power window switch RH. Refer to PWC "Removal and Installation".

NO >> Repair or replace harness.

Rear LH

REAR LH : Component Function Check

1.CHECK FUNCTION

Check rear power window motor LH operation with power window main switch or rear power window switch LH.

Is the inspection result normal?

YES >> Inspection End.

NO >> Refer to PWC "REAR LH : Diagnosis Procedure".

REAR LH : Diagnosis Procedure

Regarding Wiring Diagram information, refer to PWC "Wiring Diagram".

1.CHECK REAR POWER WINDOW MOTOR LH INPUT SIGNAL

1. Turn ignition switch OFF.

2. Disconnect rear power window motor LH connector.

3. Turn ignition switch ON.

4. Check voltage between rear power window motor LH harness connector and ground.

Is the inspection result normal?

YES >> Replace rear power window motor LH.

NO >> GO TO 2.

2.CHECK REAR POWER WINDOW MOTOR LH CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect rear power window switch LH connector.

3. Check continuity between rear power window switch LH harness connector and rear power window motor LH harness connector.

4. Check continuity between rear power window switch LH connector and ground.

Is the inspection result normal?

YES >> Replace rear power window switch LH. Refer to PWC "Removal and Installation".

NO >> Repair or replace harness.

Rear RH

REAR RH : Component Function Check

1. CHECK FUNCTION

Check rear power window motor RH operation with power window main switch or rear power window switch RH.

Is the inspection result normal?

YES >> Inspection End.

NO >> Refer to PWC "REAR RH : Diagnosis Procedure".

REAR RH : Diagnosis Procedure

Regarding Wiring Diagram information, refer to PWC "Wiring Diagram".

1.CHECK REAR POWER WINDOW MOTOR RH INPUT SIGNAL

1. Turn ignition switch OFF.

2. Disconnect rear power window motor RH connector.

3. Turn ignition switch ON.

4. Check voltage between rear power window motor RH harness connector and ground.

Is the inspection result normal?

YES >> Replace rear power window motor RH.

NO >> GO TO 2.

2.CHECK REAR POWER WINDOW MOTOR RH CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect rear power window switch RH connector.

3. Check continuity between rear power window switch RH harness connector and rear power window motor RH harness connector.

4. Check continuity between rear power window switch RH harness connector and ground.

Is the inspection result normal?

YES >> Replace rear power window switch RH. Refer to PWC "Removal and Installation".

NO >> Repair or replace harness.

Rear power window switch

Component Function Check 1. CHECK FUNCTION Check rear power window motor operation with rear power window switch. Is the inspection result normal? YES >> Inspection End. NO >> Refer ...

Door switch

Description Detects door open/close condition and transmits the signal to BCM. ...

Other materials:

Spark plugs
Replacing spark plugs Platinum-tipped spark plugs It is not necessary to replace platinum-tipped A spark plugs as frequently as conventional type spark plugs because they last much longer. Follow the maintenance log shown in the Maintenance and Schedules section of this manual. Do not ser ...

U1000 CAN Comm circuit
Description CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle multiplex communication line with high data communication speed and excellent error detection ability. Many electronic control units are equipped onto a vehicle, and each c ...

Categories


© 2017-2025 Copyright www.niveguide.com
0.0097