Nissan Versa (N17): Diagnosis system (IPDM E/R) (Without intelligent key system)

Nissan Versa 2nd generation (N17) Service Manual / Driver controls / Wiper & washer (WW) / Diagnosis system (IPDM E/R) (Without intelligent key system)

Diagnosis Description

AUTO ACTIVE TEST

Description

In auto active test, the IPDM E/R sends a drive signal to the following systems to check their operation.

Front wiper (LO, HI)
Parking lamp
License plate lamp
Tail lamp
Front fog lamp
Headlamp (LO, HI)
A/C compressor (magnet clutch)
Cooling fan

Operation Procedure

NOTE: Never perform auto active test in the following conditions.

Passenger door is open
CONSULT is connected

1. Close the hood and lift the wiper arms from the windshield. (Prevent windshield damage due to wiper operation)

NOTE: When auto active test is performed with hood opened, sprinkle water on windshield beforehand.

2. Turn the ignition switch OFF.

3. Turn the ignition switch ON, and within 20 seconds, press the driver door switch 10 times. Then turn the ignition switch OFF.

4. Turn the ignition switch ON within 10 seconds. After that the horn sounds once and the auto active test starts.

5. After a series of the following operations is repeated 3 times, auto active test is completed.

NOTE:

When auto active test has to be cancelled halfway through test, turn the ignition switch OFF.
When auto active test is not activated, door switch may be the cause. Check door switch. Refer to DLK"Component Function Check".

Inspection in Auto Active Test

When auto active test is actuated, the following operation sequence is repeated 3 times.

Concept of Auto Active Test

IPDM E/R starts the auto active test with the door switch signals transmitted by BCM via CAN communication.

Therefore, the CAN communication line between IPDM E/R and BCM is considered normal if the auto active test starts successfully.
The auto active test facilitates troubleshooting if any systems controlled by IPDM E/R cannot be operated.

Diagnosis Chart in Auto Active Test

Consult Function (IPDM E/R)

APPLICATION ITEM

CONSULT performs the following functions via CAN communication with IPDM E/R.

APPLICATION ITEM

ECU IDENTIFICATION

The IPDM E/R part number is displayed.

SELF DIAGNOSTIC RESULT

Refer to PCS "DTC Index".

DATA MONITOR

ACTIVE TEST

CAN DIAG SUPPORT MNTR

Refer to LAN "CAN Diagnostic Support Monitor".

Revision:

ECU DIAGNOSIS INFORMATION

BCM, IPDM E/R

List of ECU Reference

ECU	Reference
BCM (with Intelligent Key system)	BCS "Reference Value"
	BCS "Fail-safe"
	BCS "DTC Inspection Priority Chart"
	BCS "DTC Index"
BCM (without Intelligent Key system)	BCS "Reference Value"
	BCS "Fail-safe"
	BCS "DTC Inspection Priority Chart"
	BCS "DTC Index"
IPDM E/R (with Intelligent Key system)	PCS"Reference Value"
	PCS "Fail-safe"
	PCS "DTC Index"
IPDM E/R (without Intelligent Key system)	PCS "Reference Value"
	PCS "Fail-Safe"
	PCS "DTC Index"

WIRING DIAGRAM

FRONT WIPER AND WASHER SYSTEM

Wiring Diagram

Wiring Diagram

BASIC INSPECTION

Diagnosis system (IPDM E/R) (With intelligent key system)

Diagnosis and repair workflow

Work Flow DETAILED FLOW 1. REVIEW CUSTOMER COMPLAINT Review customer complaint. Try to obtain detailed information about the conditions when the symptom occurs. >> GO TO 2 2. VERIFY THE ...

Other materials:

Exhaust valve timing control
Exhaust valve timing control : system diagram Exhaust valve timing control : system description INPUT/OUTPUT SIGNAL CHART Sensor Input signal to ECM ECM function Actuator Crankshaft position sensor (POS) Engine speed*1 Piston position Exhaust valve timing c ...